. Ainsi, il semble que les « modules d'Young » obtenus sur grains soient plus élevés, en partie, que sur les ZAC. De plus, il semble que les surfaces de coffrage ne modifient pas les valeurs de « modules d'Young » des grains et que les « modules d'Young » obtenus au niveau des ZAC pour un contact F17 et des ZAC sombres pour un contact C20C27 soient proches voire identiques. Le coffrage C20C27 semble induire une modification des « modules

, « modules d'Young » qui sont analysées. La dispersion des valeurs de « modules d'Young » peut notamment être expliquée par l'hétérogénéité des zones grains et ZAC

, En effet, Zhu et al. 254 ont évalué sur une pâte hydratée à 15 jours, des modules variant de 15 à 35 GPa, avec une occurrence forte à 24-25 GPa. Sur pâte hydratée à 90 jours, l'intervalle des modules variait de 20 à 25 GPa, avec une occurrence forte à 25.2 ± 6.6 GPa dans l'étude de Li et al. 238 . L'intervalle de module, sur pâte de ciment âgée de 28 jours, variait de 15 à 35 GPa dans l'étude de Ren et al. 269 . De plus, les intervalles des différentes études 238,254,269,270 sont compris dans l'intervalle de « modules d'Young » évalué pour les grains, ceuxci intégrant des valeurs de « modules, ont donné des modules d'Young, sur des pâtes de ciment hydratées, variant dans des intervalles proches des intervalles de « modules, vol.238, p.65

. Gpa, , vol.17

, Par ailleurs, bien que le mode Peak Force ne permette pas de déterminer le module

W. J. Hawkins, M. Herrmann, and T. J. Ibell, Flexible formwork technologies -a state of the art review, Structural Concrete, vol.17, pp.911-946, 2016.

E. Gueit, Coloration superficielle du béton frais via l'agent de décoffrage : comparaison avec la technique de peinture à fresque, 2012.

S. Bouharoun, Comportement tribologique des huiles de décoffrage à l'interface béton/coffrage : influence de la formulation du béton, 2011.

D. Brito, J. Santos, R. Branco, and F. A. , Evaluation of the technical performance of concrete vegetable oil based release agents, Materials and Structures, vol.33, issue.4, pp.262-269, 2000.

L. Courard, F. Michel, M. , and M. , The evaluation of the surface free energy of liquids and solids in concrete technology, Construction and Building Materials, V, vol.25, issue.1, pp.260-266, 2011.

L. Libessart, P. De-caro, and C. Djelal, Correlation between adhesion energy of release agents on the formwork and demoulding performances, Construction and Building Materials, V. 76, pp.130-139, 2015.
URL : https://hal.archives-ouvertes.fr/hal-02631291

A. Rubin, Cours Master Sciences et Génie des Matériaux -Parcours 3: Design des surfaces et matériaux innovants (DSMI), 2016.

J. Cognard, Science et technologie du collage, 1ere édition, Presses polytechniques et universitaires romandes, vol.322, p.pp, 2000.

L. Courard, Contribution à l'analyse des paramètres influençant la création de l'interface entre un béton et un système de réparation. Appétence et adhérence: cause et effet d'une liaison, 1998.

, TutoPrév' Pédagogie BTP 2018 -4459, 2018.

D. Veenendaal, M. West, and P. Block, History and overview of fabric formwork: using fabrics for concrete casting, vol.12, pp.164-77, 2011.

L. Scherer and A. , Concrete Form[ing]work : Integrating patterns in flexible formwork for cast concrete, vol.5, pp.27-39, 2017.

, Syndicat français de l'échafaudage, du coffrage et de l'étaiement, 2004.

. Cimbéton, La maîtrise esthétique des parements en béton. Bétons et Ouvrages d'art, Paris, Cimbéton -Syndicat National du Béton Prêt à l'Emploi, 2005.

J. Blin-lacroix and J. Roy, , vol.1, 2011.

, Norme française NF EN 13670/CN -Exécution des strcutres en béton -Complément national à la NF EN 13670, 2013.

, Projet National CALIBE. La maîtrise de la qualité des bétons, 2001.

S. Amziane and P. Baudeau, Influence de la concentration et de la dimension des granulats visà-vis de la poussée, du béton frais sur une paroi coffrante, vol.33, pp.50-58, 2000.

N. R. Andriamanantsilavo, A. , and S. , Maturation of fresh cement paste within 1-to 10-mlarge formworks, Cement and Concrete Research, vol.34, issue.11, pp.2141-52, 2004.

S. Amziane, Contribution à l'étude des matériaux cimentaires à l'état frais, 2005.

S. Amziane and C. F. Ferraris, Cementitious paste setting using rheological and pressure measurements, ACI materials journal, vol.104, issue.2, p.137, 2007.

G. Lemaire, G. Escadeillas, and E. Ringot, Evaluating concrete surfaces using an image analysis process, Construction and Building Materials, V, vol.19, issue.8, pp.604-615, 2005.
URL : https://hal.archives-ouvertes.fr/hal-02161261

M. Martin, Etude de la texture de la surface coffrée des parements verticaux en béton, 2007.

Y. Vanhove, Contribution à l'étude du frottement d'un béton autoplaçant contre une surface métallique-Application aux poussées contre les coffrages, 2001.

C. Djelal, P. De-caro, and L. Libessart, Comprehension of demoulding mechanisms at the formwork/oil/concrete interface, Materials and Structures, vol.41, issue.3, pp.571-81, 2008.

N. Goudjil, Développement d'un nouveau procédé de décoffrage basé sur la polarisation du béton: Etude de l'aspect des parements en béton, 2012.

, Norme Française NF DTU 21 P1-1 -Travaux de bâtiment -Exécution des ouvrages en béton -Partie 1-1 : Cahier des clauses techniques types, 2017.

D. Schwartzentruber, L. Torrenti, and J. , Le grand livre des bétons, EDITIONS LE MONITEUR, p.453, 2014.

, Norme Française NF P 93-350 -Equipement de chantier -Banches industrialisées pour ouvrages en béton, 1995.

N. R. Andriamanantsilavo, S. Amziane, and P. Baudeau, Étude expérimentale sur l'évolution de la pression exercée par une pâte de ciment contre un coffrage pendant la prise, Rhéologie, pp.12-21, 2003.

M. Horgnies, P. Willieme, and O. Gabet, Characterization of the influence of the casting mould on the surface properties of concrete and on the adhesion of a protective coating, pp.27-38, 2011.

K. El-cheikh, Etude de l'interface milieu granulaire: paroi rugueuse par approches expérimentale et numérique: application aux bétons, 2015.

L. Libessart, C. Djelal, and P. De-caro, Influence des énergies de surfaces des huiles de démoulage sur les performances de décoffrage, Recueil des résumés des 24èmes Rencontres Universitaires de Génie Civil, 2006.

M. Horgnies, P. Willieme, and O. Gabet, Influence of the surface properties of concrete on the adhesion of coating: Characterization of the interface by peel test and FT-IR spectroscopy, Progress in Organic Coatings, vol.72, issue.3, pp.360-79, 2011.

N. Spitz, N. Coniglio, and M. El-mansori, Quantitative and representative adherence assessment of coated and uncoated concrete-formwork, Surface and Coatings Technology, vol.352, pp.247-56, 2018.
URL : https://hal.archives-ouvertes.fr/hal-01876401

G. K. Junior, Comportement d'interface des matériaux granulaires, 2008.

K. E. Cheikh, Comportement d'un milieu granulaire à l'interface avec une paroi -Influence de la rugosité, 2015.

M. Horgnies, C. , and J. J. , Superhydrophobic concrete surfaces with integrated microtexture, vol.52, p.10, 2014.

E. Gueit, E. Darque-ceretti, and P. Tintillier, Influence de tensioactifs sur l'hydratation du ciment à l'interface béton/coffrage, p.9, 2010.

L. Libessart, C. Djelal, and P. Caro, Influence of the type of release oil on steel formwork corrosion and facing aesthetics, Construction and Building Materials, V. 68, pp.391-401, 2014.
URL : https://hal.archives-ouvertes.fr/hal-02633718

S. Bouharoun, P. De-caro, and I. Dubois, Effect of a superplasticizer on the properties of the concrete/oil/formwork interface, Construction and Building Materials, V. 47, pp.1137-1181, 2013.
URL : https://hal.archives-ouvertes.fr/hal-02652788

P. C. Kreijger, The skin of concrete composition and properties, vol.17, pp.275-283, 1984.

. Betocib-(paris, Peaux de béton : 65 architectures contemporaines, Dunod, vol.192, p.pp, 2013.

A. Perraton, Perméabilité du béton de peau. Le choix du granulat peut-il s'avérer un élément plus déterminant que le rapport E/C ?, Bulletin des laboratoires des ponts et chaussées, issue.232, pp.59-72, 2001.

N. Bur, Etude des caractéristiques physico-chimiques de nouveaux bétons éco-respectueux pour leur résistance à l'environnement dans le cadre du développement durable, 2012.

L. Courard, C. Goffinet, and N. Migeotte, Influence of the reuse of OSB and marine plywood formworks on concrete surface aesthetics, Materials and Structures, vol.45, issue.9, pp.1331-1374, 2012.

?. Sadowski and D. Stefaniuk, The effect of surface treatment on the microstructure of the skin of concrete, Applied Surface Science, V. 427, pp.934-975, 2018.

S. Teixeira, I. Puente, and A. Santilli, Statistical model for predicting the maximum lateral pressure exerted by self-consolidating concrete on vertical formwork, Journal of Building Engineering, pp.77-86, 2017.

G. Grampeix, Vibration des bétons, 2013.

, Fascicule de documentation P 18-503 -Surfaces et parements de béton -Elements d'identification, 1989.

H. He, Analyse de l'effet d'un adjuvant biosourcé pour élaborer des matériaux cimentaires plus éco-respectueux, 2015.

C. Munzer, Etude de l'action d'un bioadjuvant aux substances extracellulaires sur la microstructure et les caractéristiques de surface de pâtes cimentaires pour des bétons plus écorespectueux, 2016.

K. Ben-ahmed, Etude de l'encrassement biologique de matériaux cimentaires en eau de rivière -Analyse de l'influence des paramètres de surface des pâtes cimentaires, 2016.

M. Martin, N. Migeotte, and C. Goffinet, Le béton apparent: influence de l'état du moule sur l'aspect des surfaces, Compte-rendu des Journées Scientifiques du (RF) 2B. Cachan, Benboudjema, Farid, 2009.

T. D. Nguyen, Étude de la zone d'interphase `` granulats calcaires poreux-pâte de ciment'': Influence des propriétés physico-mécaniques des granulats; Conséquence sur les propriétés mécaniques du mortier, 2013.

G. Lemaire, Contribution à la maîtrise de la qualité des parements de béton, 2003.

, Norme française NF EN 206, Béton -Spécification, performances, production et conformité, 2016.

, Norme française NF EN 197-1, Ciment -Partie 1 : Composition, spécifications et critères de conformité des ciments courants, 2020.

V. Baroghel-bouny, Caractérisation microstructurale et hydrique des pâtes de ciment et des bétons ordinaires et à très hautes performances, Ecole Nationale des Ponts et Chaussées, 1994.

R. Ylmén, Early Hydration of Portland Cement, 2013.

J. W. Bullard, H. M. Jennings, and R. A. Livingston, Mechanisms of cement hydration, Cement and Concrete Research, vol.41, issue.12, pp.1208-1231, 2011.

J. J. Biernacki, International Summit on Cement Hydration Kinetics and Modeling Special Edition Québec City, vol.41, pp.1206-1213, 2009.

K. L. Scrivener, V. M. John, and E. Gartner, Eco-efficient cements: Potential economically viable solutions for a low-CO2 cement-based materials industry, Cement and Concrete Research, 2018.

D. Kong, S. Huang, and D. Corr, Whether do nano-particles act as nucleation sites for C-S-H gel growth during cement hydration?, pp.98-109, 2017.

T. Conte, Impact des nano-particules sur le comportement au jeune âge et à l'état frais des matériaux à base de ciment, 2017.

E. M. Berodier, Impact of the supplementary cementitious materials on the kinetics and microstructural development of cement hydration, 2015.

P. Hou, S. Kawashima, and D. Kong, Modification effects of colloidal nanoSiO2 on cement hydration and its gel property, Composites Part B: Engineering, vol.45, issue.1, pp.440-448, 2012.

K. L. Scrivener, P. Juilland, and P. J. Monteiro, Advances in understanding hydration of Portland cement, Cement and Concrete Research, pp.38-56, 2015.

X. Wang, Modeling of Hydration, Compressive Strength, and Carbonation of Portland-Limestone Cement (PLC) Concrete, Materials, V, vol.10, issue.2, p.115, 2017.

S. Rahimi-aghdam, Z. P. Ba?ant, A. Qomi, and M. J. , Cement hydration from hours to centuries controlled by diffusion through barrier shells of C-S-H, Journal of the Mechanics and Physics of Solids, pp.211-235, 2017.

M. D. Nguyen, Modélisation des couplages entre hydratation et dessiccation des matériaux cimentaires à l'issue du décoffrage. Étude de la dégradation des propriétés de transfert, Ecole Nationale des Ponts et Chaussées, 2009.

K. L. Scrivener and A. Nonat, Hydration of cementitious materials, present and future, Cement and Concrete Research, vol.41, issue.7, pp.651-65, 2011.

L. Nicoleau and A. Nonat, A new view on the kinetics of tricalcium silicate hydration, Cement and Concrete Research, pp.1-11, 2016.

F. Bellmann, T. Sowoidnich, and H. Ludwig, Dissolution rates during the early hydration of tricalcium silicate, Cement and Concrete Research, pp.108-124, 2015.

E. Gartner, Discussion of the paper 'A new view on the kinetics of tricalcium silicate hydration, Cement and Concrete Research, vol.86, pp.114-121, 2016.

P. Juilland, E. Gallucci, and R. Flatt, Dissolution theory applied to the induction period in alite hydration, Cement and Concrete Research, vol.40, issue.6, pp.831-875, 2010.

A. Bazzoni, Study of early hydration mechanisms of cement by means of electron microscopy, 2014.

E. Gartner, I. Maruyama, C. , and J. , A new model for the C-S-H phase formed during the hydration of Portland cements, Cement and Concrete Research, pp.95-106, 2017.

S. Aydin-gunay, Influence de la cinétique d'hydratation des phases aluminates en présence de sulfate de calcium sur celles des phases silicates. Conséquences sur l'Optimum de sulfatage des ciments, 2012.

T. T. Bach, Evolution physico-chimique des liants bas PH hydratés: influence de la température et mécanisme de rétention des alcalins, 2010.

S. Stephant, Etude de l'influence de l'hydratation des laitiers sur les propriétés de transfert gazeux dans les matériaux cimentaires, 2015.

C. Labbez, I. Pochard, and B. Jönsson, C-S-H/solution interface: Experimental and Monte Carlo studies, Cement and Concrete Research, vol.41, issue.2, pp.161-169, 2011.
URL : https://hal.archives-ouvertes.fr/hal-00564364

I. G. Richardson, The calcium silicate hydrates, Cement and Concrete Research, vol.38, issue.2, pp.137-58, 2008.

H. Alkhateb, A. Al-ostaz, A. H. Cheng, and .. , Materials Genome for Graphene-Cement Nanocomposite, Journal of Nanomechanics and Micromechanics, issue.3, pp.67-77, 2013.

C. Plassard, Etude fondamentale des mécanismes à l'origine de la cohésion des nanoparticules de silicates de calcium hydratés par microscopie à force atomique, 2005.

J. Haas, Etude expérimentale et modélisation thermodynamique du système CaO-SiO2-(Al2O3)-H2O, 2012.

M. Gassó, Impact of alkali salts on the kinetics and microstructural development of cementitious systems, 2015.

B. Lothenbach and A. Nonat, Calcium silicate hydrates: Solid and liquid phase composition, Cement and Concrete Research, pp.57-70, 2015.

G. Plusquellec, Analyse in situ de suspensions de silicate de calcium hydraté : application aux interactions ioniques à la surface des particules, 2014.

H. Jennings, Z. Bittnar, P. J. Bartos, and J. N?me?ek, The Colloid/Nanogranular Nature of Cement Paste and Properties, Nanotechnology in Construction 3, pp.27-36, 2009.

S. Garrault-gauffinet, Etude expérimentale et par simulation numérique de la cinétique de croissance et de la structure des hydrosilicates de calcium, produits d'hydratation des silicates tricalcique et dicalcique, 1998.

A. Plassais, Nanoporosité, texture et propriétés mécaniques de pâtes de ciments, 2003.

G. Constantinides and F. Ulm, The nanogranular nature of C-S-H, Journal of the Mechanics and Physics of Solids, vol.55, issue.1, pp.64-90, 2007.

H. Jennings, Refinements to colloid model of C-S-H in cement: CM-II, Cement and Concrete Research, vol.38, issue.3, pp.275-89, 2008.

T. C. Powers, Structure and Physical Properties of Hardened Portland Cement Paste, Journal of the American Ceramic Society, vol.41, issue.1, pp.1-6, 1958.

R. F. Feldman and P. J. Sereda, A model for hydrated Portland cement paste as deduced from sorption-length change and mechanical properties, Matériaux et Constructions, V, vol.1, issue.6, pp.509-529, 1968.

M. Daimon, S. A. Abo-el-enein, and G. Rosara, Pore Structure of Calcium Silicate Hydrate in Hydrated Tricalcium Silicate, Journal of the American Ceramic Society, vol.60, pp.110-114, 1977.

H. Jennings, A model for the microstructure of calcium silicate hydrate in cement paste, Cement and Concrete Research, vol.30, issue.1, pp.101-117, 2000.

H. Jennings, Colloid model of C-S-H and implications to the problem of creep and shrinkage, p.12, 2004.

M. A. Etzold, P. J. Mcdonald, and A. F. Routh, Growth of sheets in 3D confinements -a model for the C-S-H meso structure, vol.63, pp.137-179, 2014.

G. Constantinides and F. Ulm, The effect of two types of C-S-H on the elasticity of cement-based materials: Results from nanoindentation and micromechanical modeling, Cement and Concrete Research, vol.34, issue.1, pp.67-80, 2004.

H. M. Jennings, J. W. Bullard, and J. J. Thomas, Characterization and Modeling of Pores and Surfaces in Cement Paste: Correlations to Processing and Properties, pp.5-29, 2008.

A. Morandeau, Carbonatation atmosphérique des systèmes cimentaires à faible teneur en portlandite, 2013.

S. Hajilar and B. Shafei, Assessment of structural, thermal, and mechanical properties of portlandite through molecular dynamics simulations, Journal of Solid State Chemistry, pp.164-74, 2016.

E. Gallucci and K. Scrivener, Crystallisation of calcium hydroxide in early age model and ordinary cementitious systems, Cement and Concrete Research, vol.37, issue.4, pp.492-501, 2007.

S. Galmarini, A. Aimable, and N. Ruffray, Changes in portlandite morphology with solvent composition: Atomistic simulations and experiment, Cement and Concrete Research, vol.41, issue.12, pp.1330-1338, 2011.

S. Galmarini, Atomistic Simulation of Cementitious Systems, 2013.

N. Hernandez, J. Lizarazo-marriaga, and M. A. Rivas, Petrographic characterization of Portlandite crystal sizes in cement pastes affected by different hydration environments, Construction and Building Materials, V. 182, pp.541-550, 2018.

M. Bouasker, P. Mounanga, and P. Turcry, Chemical shrinkage of cement pastes and mortars at very early age: Effect of limestone filler and granular inclusions, vol.30, pp.13-22, 2008.
URL : https://hal.archives-ouvertes.fr/hal-00315319

V. Bonavetti, H. Donza, and G. Menéndez, Limestone filler cement in low w/c concrete: A rational use of energy, Cement and Concrete Research, vol.33, issue.6, pp.865-71, 2003.

I. Guénot-delahaie, Contribution à l'analyse physique et à la modélisation du fluage propre du béton, Ecole Nationale des Ponts et Chaussées, 1996.

N. C. Collier, J. H. Sharp, and N. B. Milestone, The influence of water removal techniques on the composition and microstructure of hardened cement pastes, Cement and Concrete Research, vol.38, issue.6, pp.737-781, 2008.

J. Hot, Influence des polymères de type superplastifiants et agents entraineurs d'air sur la viscosité macroscopique des matériaux cimentaires, 2013.

A. Bordy, Influence des conditions thermo-hydriques de conservation sur l'hydratation de matériaux cimentaires à base d'une fine recyclée, 2016.

J. Zhang and G. W. Scherer, Comparison of methods for arresting hydration of cement, Cement and Concrete Research, vol.41, issue.10, pp.1024-1060, 2011.

K. Ioannidou, K. J. Krakowiak, and M. Bauchy, Mesoscale texture of cement hydrates, Proceedings of the National Academy of Sciences, vol.113, pp.2029-2063, 2016.
URL : https://hal.archives-ouvertes.fr/hal-01455017

C. Bresciani, Simulation numérique de l'hydratation et du développement des propriétés physiques et mécaniques d'une pâte de ciment afin de sélectionner de nouveaux ajouts minéraux, 2008.

A. Peled, J. Castro, and W. J. Weiss, Atomic force and lateral force microscopy (AFM and LFM) examinations of cement and cement hydration products, pp.48-55, 2013.

L. Courard, Durabilité des réparations de béton : entre théorie et pratique, pp.31-40, 2006.

L. Courard, T. Piotrowski, and A. Garbacz, Near-to-surface properties affecting bond strength in concrete repair, vol.46, pp.73-80, 2014.

A. Backelandt, Etude des mécanismes d'adhésion à l'interface résine/ciment en vue de la réparation des ouvrages de génie civil, 2005.

M. Thomann, Connexions par adhérence pour les ponts mixtes acier-béton, 2005.

A. Garbacz, L. Courard, and K. Kostana, Characterization of concrete surface roughness and its relation to adhesion in repair systems, Materials Characterization, vol.56, pp.281-290, 2006.

T. Mauroux, Impact du séchage sur les propriétés d'adhérence entre un mortier et un support: influence de l'adjuvantation par des éthers cellulose, 2011.

B. Bissonnette, L. Courard, and M. Jolin, Adhérence des réparations en béton: évaluation et facteurs d'influence, 2014.

G. Francius, R. El-zein, and L. Mathieu, Nano-exploration of organic conditioning film formed on polymeric surfaces exposed to drinking water, Water Research, pp.155-63, 2017.
URL : https://hal.archives-ouvertes.fr/hal-01912919

M. Clavel and P. Bompard, Endommagement et rupture des matériaux. 2 -Matériaux non métalliques et biomatériaux, assemblages et problèmes industriels, v, vol.2, p.224, 2009.

D. Maugis, 4 -Adhesion of Solids: Mechanical Aspects, Modern Tribology Handbook, Two Volume Set, vol.5, 2000.

T. H. Qhach, Etude de la durabilité d'un primaire epoxy anticorrosion: rôle de l'interphase polymère/métal et conséquence sur l'adhérence, 2011.

J. Israelachvili, Intermolecular and surface forces, vol.676, p.pp, 2011.

A. Gerschel, Liaisons intermoléculaires. Les forces en jeu dans la matière condensée, InterEditions-CNRS Editions, vol.285, p.pp, 1995.

C. Gruber and P. Martin, De l'atome antique à l'atome quantique, 2013.

F. Mege, AFM à contact résonant: développement et modélisation, 2011.

D. Sicard, Caractérisation par microscopie à force atomique des arrangements protéine/sucre impliquant la lectine PA-IL de la bactérie Pseudomonas aeruginosa, 2012.

F. Zuttion, Effet inhibiteur des glycoclusters dans l'adhésion bactérienne de Pseudomonas aeruginosacaractérisé par Microscopie à Force Atomique: de la molécule à la cellule, 2016.

F. Detrez, Microscopie à force atomique, 2010.
URL : https://hal.archives-ouvertes.fr/tel-00779207

B. Sarrazin, Propriétés mécaniques de bicouches et de capsules polymères résolues à l'échelle nanométrique. Etude par microscopie à force atomique, 2015.

O. Pietrement, Imagerie et caractérisation nanomécanique des surfaces par microscopie à force atomique, 2000.

S. Alvo, Étude, modélisation et mesure des forces d'adhésion à l'échelle microscopique, 2012.

S. Lesko, Mesure des forces interparticulaires par microscopie à force atomique -Application à la cohésion du ciment, 2005.

G. Béranger and H. Mazille, Approche scientifique des surfaces. Caractérisation et propriétés, 2005.

T. Young, An Essay on the Cohesion of Fluids, Philosophical Transactions of the Royal Society of London, pp.65-87

D. K. Owens and R. C. Wendt, Estimation of the surface free energy of polymers, Journal of Applied Polymer Science, vol.13, issue.8, pp.1741-1748, 1969.

, Norme française NF EN 828 -Adhésifs -Mouillabilité -Détermination par mesurage de l'angle de contact et de l'énergie superficielle libre de la surface solide, 2013.

D. Coutelier, Contribution à l'amélioration des lois de comportement pour la simulation numérique du choc sur les structures composites du domaine des transports, Recherche -Transports -Sécurité, vol.23, issue.90, pp.29-40, 2006.

K. L. Mittal, A. , and T. , Adhesion in microelectronics, 2014.

G. A. Rao, F. Sultana, and K. Pandurangan, Studies on the pull-out strength of ribbed bars in high-strength concrete." proceeding, FraMCos-6 conference. International Association of Fracture Mechanics for Concrete and Concrete Structures. Part, vol.5, pp.5-17, 2004.

, Norme française NF EN ISO 10365 -Adhésifs -Désignation des principaux faciès de rupture, 1995.

, NF EN ISO 4624 -Peintures et vernis -Essai de traction, 2016.

, NF EN 1542 -Produits et systèmes pour la protection et la réparation des structures en béton -Méthodes d'essais -Mesurage de l'adhérence par traction directe, 1999.

, Norme française NF P 98-282 -Essais relatifs aux chaussées -Produits d'étanchéité pour ouvrages d'art -Mesure d'adhérence des produits au support, 2007.

, ASTM D 4541 -Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers, 2017.

J. L. Aguiar, Essais d'adhérence des époxydes au béton hydraulique (Tests on bonding between epoxies and hydraulic concrete), Materials and Structures, vol.26, issue.2, pp.90-97, 1993.

L. Courard and B. Bissonnette, Essai dérivé de l'essai d'adhérence pour la caractérisation de la cohésion superficielle des supports en béton dans les travaux de réparation: analyse des paramètres d'essai, Matériaux et Constructions, pp.342-350, 2004.

A. Tixier, Analyse du comportement de l'interface acier-béton pas essai push-in: mesures par fibres optiques et modélisation par éléments finis, 2013.

N. Dominguez-ramirez, Etude de la liaison acier-béton : de la modélisation du phénomène à la formulation d'un élément fini enrichi "béton armé, 2005.

L. Chiriatti, Etude de l'adhérence armature-béton, influence des granulats de béton recyclé et apport des mesures acoustiques, 2018.

, Norme française NF EN ISO 8510-2 -Essai de pelage pour un assemblage collé flexible-sur-rigide -Partie 2 : Pelage à 180 degrés, 2011.

, Norme française NF EN 1464 -Adhésifs -Détermination de la résistance au pelage des assemblages -Méthode des galets mobiles, 2010.

J. Lee and M. Lopez, An Experimental Study on Fracture Energy of Plain Concrete, International Journal of Concrete Structures and Materials, V, vol.8, issue.2, pp.129-168, 2014.

F. A. Gilabert, K. Van-tittelboom, and E. Tsangouri, Determination of strength and debonding energy of a glass-concrete interface for encapsulation-based self-healing concrete, pp.76-93, 2017.

S. Benayoun and J. Hantzpergue, Les tests d'adhérence appliqués aux revêtements minces : une synthèse bibliographique, Matériaux & Techniques, V. 92, Nos, pp.23-32, 2004.

E. Leforestier, J. Costini, and E. Darque-ceretti, Lebanese Science Journal, vol.2, issue.1, p.25, 2001.

J. Sauvage, Caractérisation et modélisation de l'adhérence dans les assemblages collés, 2016.

V. G. Papadakis, E. J. Pedersen, and H. Lindgreen, An AFM-SEM investigation of the effect of silica fume and fly ash on cement paste microstructure, Journal of Materials Science, vol.34, issue.4, pp.683-690, 1999.

K. Velez, S. Maximilien, and D. Damidot, Determination by nanoindentation of elastic modulus and hardness of pure constituents of Portland cement clinker, Cement and Concrete Research, vol.31, issue.4, pp.555-561, 2001.

G. Constantinides, F. Ulm, V. Vliet, and K. , On the use of nanoindentation for cementitious materials, vol.36, pp.191-196, 2003.

F. Ulm, M. Vandamme, and C. Bobko, Statistical Indentation Techniques for Hydrated Nanocomposites: Concrete, Bone, and Shale, Journal of the American Ceramic Society, vol.90, issue.9, pp.2677-92, 2007.
URL : https://hal.archives-ouvertes.fr/hal-00555551

T. Howind, J. J. Hughes, and W. Zhu, Mapping of mechanical properties of cement paste microstructures, 2011.

P. Trtik, B. Münch, and P. Gasser, Focussed ion beam nanotomography reveals the 3D morphology of different solid phases in hardened cement pastes: FIB-nt REVEALS 3D MORPHOLOGY OF DIFFERENT SOLID PHASES, Journal of Microscopy, issue.3, pp.234-276, 2011.

C. A. Jones, Z. C. Grasley, and J. A. Ohlhausen, Measurement of elastic properties of calcium silicate hydrate with atomic force microscopy, vol.34, pp.468-77, 2012.

L. Ferrari, J. Kaufmann, and F. Winnefeld, Reaction of clinker surfaces investigated with atomic force microscopy, Construction and Building Materials, V. 35, pp.92-98, 2012.

H. Asgari, A. Ramezanianpour, and H. Butt, Effect of water and nano-silica solution on the early stages cement hydration, Construction and Building Materials, V. 129, pp.11-24, 2016.

H. Asgari, A. A. Ramezanianpour, and H. J. Butt, Nano-mechanical Behavior of Calcium Silicate Hydrate and Calcium Hydroxide in Cement Paste: Elevated Peak-Force Study, International Journal of Civil Engineering, 2016.

Z. Khawaja, Analyse des états de surfaces en science des matériaux : Caractérisation multiéchelles par ondelette et détermination de l'anisotropie des surfaces, 2014.

, Norme française NF EN ISO 4287 -Spécification géométrique des produits (GPS) -Etat de surface : Méthode du profil -Termes, définitions et paramètres d'état de surface, 1998.

, Norme française NF EN 17450-1 -Spécification géométrique des produits (GPS) -Concepts généraux -Partie 1 : modèle pour la spécification et la vérification géométriques, 2012.

R. Holze, Surface and interface analysis: an electrochemists toolbox, vol.300, p.pp, 2009.

M. Brogly, H. Awada, and O. Noel, Contact atomic force microscopy: a powerful tool in adhesion science, Applied Scanning Probe Methods XI, pp.73-95, 2009.

M. Brogly, Adhésifs polymères : mécanismes et propriétés d'adhésion, 2010.

S. Werner, I. Neumann, and K. Thienel, A fractal-based approach for the determination of concrete surfaces using laser scanning techniques: a comparison of two different measuring systems, Materials and Structures, vol.46, pp.245-54, 2013.

, Norme européenne NF EN ISO 25178-2 -Spécification géométrique des produits (GPS) -État de surface : surfacique -Partie 2 : termes, définitions et paramètres d'états de surface, 2012.

?. Sadowski, A. ?ak, and J. Ho?a, Multi-sensor evaluation of the concrete within the interlayer bond with regard to pull-off adhesion, Archives of Civil and Mechanical Engineering, vol.18, issue.2, pp.573-82, 2018.

P. Trtik, J. Dual, and B. Muench, Limitation in obtainable surface roughness of hardened cement paste: 'virtual' topographic experiment based on focussed ion beam nanotomography datasets, Journal of Microscopy, vol.232, issue.2, pp.200-206, 2008.

M. Chollet and M. Horgnies, Analyses of the surfaces of concrete by Raman and FT-IR spectroscopies: comparative study of hardened samples after demoulding and after organic post-treatment, Surface and Interface Analysis, vol.43, issue.3, pp.714-739, 2011.

S. Roux, Evaluation des risques de biodégradation des bétons en contact avec une eau douce naturelle, 2008.

O. A. Maslova, Spectroscopie et imagerie Raman de matériaux inhomogènes, 2014.

D. Kim, J. G. Kim, and C. N. Chu, Aging effect on the wettability of stainless steel, Materials Letters, pp.18-20, 2016.

Y. Hedberg, M. Karlsson, and E. Blomberg, Correlation between surface physicochemical properties and the release of iron from stainless steel AISI 304 in biological media, Colloids and Surfaces B: Biointerfaces, vol.122, pp.216-238, 2014.

M. Mantel and J. Wightman, Influence of the surface chemistry on the wettability of stainless steel, Surface and Interface Analysis, vol.21, issue.9, pp.595-605, 1994.

A. Benatmane, Développement de la microscopie interférométrique pour une meilleure analyse morphologique des couches minces et épaisses des matériaux semiconducteurs et optiques, 2003.

K. L. Apedo, C. Munzer, and H. He, Cement paste surface roughness analysis using coherence scanning interferometry and confocal microscopy, Materials Characterization, pp.108-127, 2015.

R. Claveau, P. Montgomery, and M. Flury, Coherence scanning interferometry allows accurate characterization of micrometric spherical particles contained in complex media, Ultramicroscopy, p.112859, 2020.
URL : https://hal.archives-ouvertes.fr/hal-02391406

K. L. Apedo, P. Montgomery, and N. Serres, Geometrical roughness analysis of cement paste surfaces using coherence scanning interferometry and confocal microscopy, Materials Characterization, pp.212-236, 2016.
URL : https://hal.archives-ouvertes.fr/hal-02147730

P. Mondal, Nanomechanical Properties of Cementitious Materials, 2008.

S. Roux, F. Feugeas, and A. Cornet, Biodeterioration of Mortars and Cement Paste studied using ESEM, STEM and EDS, Microscopy and Analysis, pp.19-21, 2006.
URL : https://hal.archives-ouvertes.fr/hal-02947391

A. Peled and J. Weiss, Hydrated cement paste constituents observed with Atomic Force and Lateral Force Microscopy, Construction and Building Materials, V, vol.25, issue.11, pp.4299-302, 2011.

J. Kaufmann, F. Winnefeld, and R. Zurbriggen, Polymer dispersions and their interaction with mortar constituents and ceramic tile surfaces studied by zeta-potential measurements and atomic force microscopy, vol.34, pp.604-615, 2012.

Z. Bajja, Influence de la microstructure sur le transport diffusif des pâtes, mortiers et bétons à base de CEM I avec ajout de fumée de silice, 2016.

E. Ortega, O. Rodríguez-martínez, and M. Figueroa-labastida, Long-term influence of chitin concentration on the resistance of cement pastes determined by atomic force microscopy, physica status solidi, vol.213, issue.12, pp.3110-3116, 2016.

R. J. Kirkpatrick, J. L. Yarger, and P. F. Mcmillan, Raman spectroscopy of C-S-H, tobermorite, and jennite, pp.93-102, 1997.

L. Black, C. Breen, and J. Yarwood, Hydration of tricalcium aluminate (C3A) in the presence and absence of gypsum-studied by Raman spectroscopy and X-ray diffraction, Journal of Materials Chemistry, vol.16, issue.13, p.1263, 2006.

G. Renaudin, R. Segni, and D. Mentel, A Raman Study of the Sulfated Cement Hydrates: Ettringite and Monosulfoaluminate, Journal of Advanced Concrete Technology, issue.3, pp.299-312, 2007.
URL : https://hal.archives-ouvertes.fr/hal-00187345

F. Liu, Z. Sun, and C. Qi, Raman Spectroscopy Study on the Hydration Behaviors of Portland Cement Pastes during Setting, Journal of Materials in Civil Engineering, vol.27, issue.8, p.4014223, 2015.

F. Liu and Z. Sun, Chemical mapping of cement pastes by using confocal Raman spectroscopy, Frontiers of Structural and Civil Engineering, vol.10, issue.2, pp.168-73, 2016.

A. Szcze?, M. Czemierska, and A. Jarosz-wilko?azka, Calcium carbonate formation on mica supported extracellular polymeric substance produced by Rhodococcus opacus, Journal of Solid State Chemistry, pp.212-233, 2016.

M. Frías, R. De-la-villa, and R. García, Carbonation-Induced Mineralogical Changes in Coal Mining Waste Blended Cement Pastes and Their Influence on Mechanical and Microporosity Properties, p.169, 2018.

M. Torres-carrasco, A. Campo, M. A. Rubia, and . De-la, In situ full view of the Portland cement hydration by confocal Raman microscopy, Journal of Raman Spectroscopy, vol.50, issue.5, pp.720-750, 2019.

N. Spitz, N. Coniglio, and M. El-mansori, On functional signatures of bare and coated formwork skin surfaces, Construction and Building Materials, V. 189, pp.560-567, 2018.
URL : https://hal.archives-ouvertes.fr/hal-01876403

W. T. Choi, K. Oh, and P. M. Singh, Wettability control of stainless steel surfaces via evolution of intrinsic grain structures, Journal of Materials Science, vol.51, issue.11, pp.5196-206, 2016.

F. Goossens, Modélisation du processus de polissage: identification des effets et des phénoménologies induits par l'usinage abrasif, 2015.

C. Virgilio, Caractérisation du mouillage de surfaces micro/nanostructurées par méthode acoustique haute fréquence: application aux traitements humides dans l'industrie de la microélectronique, 2017.

H. Awada, G. Castelein, and M. Brogly, Quantitative determination of surface energy using atomic force microscopy: the case of hydrophobic/hydrophobic contact and hydrophilic/hydrophilic contact, Surface and Interface Analysis, vol.37, issue.9, pp.755-64, 2005.

M. Brogly, O. Noel, and H. Awada, A nanoscale study of the adhesive contact, Comptes Rendus Chimie, vol.9, issue.1, pp.99-110, 2006.

W. C. Oliver and G. Pharr, An improved technique for determining hardness and elastic modulus, Journal of Materials Research, vol.7, issue.6, pp.1564-83, 1992.
URL : https://hal.archives-ouvertes.fr/hal-01518596

P. D. Garcia and R. Garcia, Determination of the Elastic Moduli of a Single Cell Cultured on a Rigid Support by Force Microscopy, Biophysical Journal, vol.114, issue.12, pp.2923-2955, 2018.

R. D. O'rorke, T. W. Steele, and H. K. Taylor, Bioinspired fibrillar adhesives: a review of analytical models and experimental evidence for adhesion enhancement by surface patterns, Journal of Adhesion Science and Technology, vol.30, issue.4, pp.362-91, 2016.

D. Maugis, Adhesion of Solids: Mechanical Aspects, p.41, 2001.

G. Guillonneau, Nouvelles techniques de nano-indentation pour des conditions expérimentales difficiles: très faibles enfoncements, surfaces rugueuses, température, 2012.

T. J. Young, M. A. Monclus, and T. L. Burnett, The use of the Peak Force Quantitative Nanomechanical Mapping AFM-based method for high-resolution Young's modulus measurement of polymers, Measurement Science and Technology, vol.22, issue.12, 2011.

N. Oumarou, Caractérisation mécanique de systèmes film-substrat par indentation instrumentée (nanoindentation) en géométrie sphère-plan, 2009.

D. François, A. Pineau, and A. Zaoui, Comportement mécanique des matériaux. Viscoplasticité, endommagement, mécanique de la rupture, vol.494, p.pp, 1993.

E. Barthel, Adhesive elastic contacts: JKR and more, Journal of Physics D: Applied Physics, vol.41, issue.16, p.163001, 2008.
URL : https://hal.archives-ouvertes.fr/hal-00256886

C. A. Jones, Contact mechanics based mechanical characterization of Portland cement paste, 2011.

L. F. Da-silva, A. Öchsner, A. , and R. D. , Handbook of Adhesion Technology, 2011.

M. Ciavarella, J. Joe, and A. Papangelo, The role of adhesion in contact mechanics, Journal of The Royal Society Interface, vol.16, issue.151, p.20180738, 2019.

K. L. Johnson and J. A. Greenwood, An Adhesion Map for the Contact of Elastic Spheres, Journal of Colloid and Interface Science, vol.192, issue.2, pp.326-359, 1997.

Y. M. Efremov, D. V. Bagrov, and M. P. Kirpichnikov, Application of the Johnson-Kendall-Roberts model in AFM-based mechanical measurements on cells and gel, Colloids and Surfaces B: Biointerfaces, pp.131-140, 2015.

K. Anselme, P. Davidson, and A. M. Popa, The interaction of cells and bacteria with surfaces structured at the nanometre scale, Acta Biomaterialia, vol.6, issue.10, pp.3824-3870, 2010.
URL : https://hal.archives-ouvertes.fr/hal-02384171

H. Butt, B. Cappella, and M. Kappl, Force measurements with the atomic force microscope: Technique, interpretation and applications, Surface Science Reports, vol.59, pp.1-152, 2005.

P. E. Stutzman, C. , and J. R. , Specimen preparation for scanning electron microscopy, Proceedings of the international conference on cement microscopy, vol.21, pp.10-22, 1999.

K. O. Kjellsen, A. Monsøy, and K. Isachsen, Preparation of flat-polished specimens for SEM-backscattered electron imaging and X-ray microanalysis-importance of epoxy impregnation, Cement and concrete research, vol.33, issue.4, pp.611-616, 2003.

M. Miller, C. Bobko, and M. Vandamme, Surface roughness criteria for cement paste nanoindentation, Cement and Concrete Research, vol.38, issue.4, pp.467-76, 2008.
URL : https://hal.archives-ouvertes.fr/hal-00555544

P. Trtik, J. Kaufmann, and U. Volz, On the use of peak-force tapping atomic force microscopy for quantification of the local elastic modulus in hardened cement paste, Cement and Concrete Research, vol.42, issue.1, pp.215-236, 2012.

V. N. Dwivedi, S. S. Das, and N. B. Singh, Portland cement hydration in the presence of admixtures: black gram pulse and superplasticizer, Materials Research, vol.11, issue.4, pp.427-458, 2008.

D. L. Nguyen, Nouvelle méthodologie d'identification des propriétés mécaniques locales d'un matériau hétérogène par nanoindentation: application aux matériaux du génie civil, 2017.

W. Li, S. Kawashima, and J. Xiao, Comparative investigation on nanomechanical properties of hardened cement paste, Materials and Structures, vol.49, issue.5, pp.1591-604, 2016.

P. Trtik, B. Münch, L. , and P. , A critical examination of statistical nanoindentation on model materials and hardened cement pastes based on virtual experiments, vol.31, pp.705-719, 2009.

G. Lomboy, S. Sundararajan, and K. Wang, A test method for determining adhesion forces and Hamaker constants of cementitious materials using atomic force microscopy, Cement and Concrete Research, vol.41, issue.11, pp.1157-66, 2011.

P. Stutzman, L. , and S. , Phase composition analysis of the NIST reference clinkers by optical microscopy and X-ray powder diffraction, p.44, 1441.

L. Struble and P. Stutzman, Epoxy impregnation of hardened cement for microstructural characterization, Journal of Materials Science Letters, issue.6, pp.632-634, 1989.

W. Zhu, M. T. Fonteyn, and J. Hughes, Nanoindentation study of resin impregnated sandstone and early-age cement paste specimens, Nanotechnology in Construction, vol.3, pp.403-408, 2009.

, Norme française NF EN ISO 6506-1 Matériaux métalliques -Essai de dureté Brinell -Partie 1 : Méthode d'essai, 2014.

L. Odoni, Propriétés mécaniques et effets d'échelle, 1999.

L. Charleux, Micromécanique de l'essai d'indentation : expériences et simulations, 2006.

E. Renner, Vers l'identification d'une loi de plasticité monocristalline par analyse topographique d'empreintes de nanoindentation Berkovich, 2016.

R. Hin, Comportement à l'indentation et à la rayure de verres métalliques et silicatés, 2017.

J. J. Chen, L. Sorelli, and M. Vandamme, A Coupled Nanoindentation/SEM-EDS Study on Low Water/Cement Ratio Portland Cement Paste: Evidence for C-S-H/Ca(OH) 2 Nanocomposites, Journal of the American Ceramic Society, 2010.
URL : https://hal.archives-ouvertes.fr/hal-00555495

J. Loubet, Courbes d'indentation et effet d'échelle : Quelques cas expérimentaux, 1986.

J. M. Antunes, L. F. Menezes, and J. Fernandes, Three-dimensional numerical simulation of Vickers indentation tests, International Journal of Solids and Structures, vol.43, issue.3, pp.784-806, 2006.

C. Hu, L. , and Z. , Micromechanical investigation of Portland cement paste, Construction and Building Materials, V. 71, pp.44-52, 2014.

W. Zhu, J. J. Hughes, and N. Bicanic, Nanoindentation mapping of mechanical properties of cement paste and natural rocks, Materials Characterization, vol.58, pp.1189-98, 2007.

W. Zhu, T. Howind, and S. Barbhuiya, Nanomechanical study of cement pastes by statistical nanoindentation and PeakForce QNM, p.8, 2012.

J. Xu, D. J. Corr, and S. P. Shah, Nanomechanical investigation of the effects of nanoSiO2 on C-S-H gel/cement grain interfaces, pp.7-17, 2015.

Q. Liu, T. Tong, and S. Liu, Investigation of using hybrid recycled powder from demolished concrete solids and clay bricks as a pozzolanic supplement for cement, Construction and Building Materials, V. 73, pp.754-63, 2014.

F. Ulm, M. Vandamme, and H. M. Jennings, Does microstructure matter for statistical nanoindentation techniques?, vol.32, pp.92-99, 2010.
URL : https://hal.archives-ouvertes.fr/hal-00555531

M. Vandamme, The Nanogranular Origin of Concrete Creep: A Nanoindentation Investigation of Microstructure and Fundamental Properties of Calcium-Silicate-Hydrates, 2008.

J. J. Hughes and P. Trtik, Micro-mechanical properties of cement paste measured by depthsensing nanoindentation: a preliminary correlation of physical properties with phase type, Materials Characterization, vol.53, pp.223-254, 2004.

J. Xu, D. J. Corr, and S. P. Shah, Nanomechanical properties of C-S-H gel/cement grain interface by using nanoindentation and modulus mapping, Journal of Zhejiang University-SCIENCE A, vol.16, issue.1, pp.38-46, 2015.

P. Mondal, S. P. Shah, and L. Marks, A reliable technique to determine the local mechanical properties at the nanoscale for cementitious materials, Cement and Concrete Research, vol.37, issue.10, pp.1440-1444, 2007.

P. Acker, Micromechanical analysis of creep and shrinkage mechanisms, Cambridge, pp.15-21, 2001.

. Bruker, Application Note 128 -Quantitative Mechanical Property Mapping at the Nanoscale with PeakForce QNM, 2012.

L. D. Mitchell, M. Prica, and J. Birchall, Aspects of Portland cement hydration studied using atomic force microscopy, Journal of Materials Science, vol.31, issue.16, pp.4207-4219, 1996.

T. Yang, B. Keller, and E. Magyari, AFM investigation of cement paste in humid air at different relative humidities, Journal of Physics D: Applied Physics, vol.35, issue.8, p.25, 2002.

Y. Sáez-de-ibarra, J. J. Gaitero, and E. Erkizia, Atomic force microscopy and nanoindentation of cement pastes with nanotube dispersions, pp.1076-81, 2006.

M. Kamali and A. Ghahremaninezhad, A Study of Calcium-Silicate-Hydrate/Polymer Nanocomposites Fabricated Using the Layer-By-Layer Method, Materials, V, vol.11, issue.4, p.527, 2018.

E. Horszczaruk, E. Mijowska, and R. J. Kalenczuk, Nanocomposite of cement/graphene oxide -Impact on hydration kinetics and Young's modulus, Construction and Building Materials, V. 78, pp.234-276, 2015.

M. Ren, T. Shi, and D. J. Corr, Mechanical Properties of Micro-regions in Cement-based Material based on the PeakForce QNM Mode of AFM, Journal of Wuhan University of Technology-Mater. Sci. Ed., V, vol.34, issue.4, pp.893-902, 2019.

X. Zhu, Y. Gao, and Z. Dai, Effect of interfacial transition zone on the Young's modulus of carbon nanofiber reinforced cement concrete, vol.107, pp.49-63, 2018.

C. Caër, Caractérisation par nanoindentation et modélisation micromécanique de l'activation de mécanismes inélastiques: plasticité cristalline et transformation martensitique, 2013.

J. Leuvrey, La nouvelle norme des bétons NF EN 206 -La_nouvelle_norme_des_bétons_NF_EN_206.pdf, 2006.

. Cimbéton, Ciments et bétons. L'essentiel, 2005.

, Norme française NF EN 196-3 -Méthodes d'essai des ciments -Partie 3 : détermination du temps de prise et de la stabilité, 2017.

A. Rannée, Développement de revêtements photopolymères pour le démoulage de coffrages de béton, 2018.

, Norme française NF EN ISO 3274 -Spécification géométrique des produits (GPS) -État de surface : méthode du profil -Caractéristiques nominales des appareils à contact (palpeur), 1998.

R. Leach, L. Brown, and J. Jiang, Guide to the measurement of smooth surface topography using coherence scanning interferometry, National Physical Laboratory, issue.108, 2008.

D. Reolon, Interférométrie spectrale pour la mesure de dispersion et la géométrie de surface, 2006.

J. Petzing, J. Coupland, and R. Leach, The Measurement of Rough Surface Topography using Coherence Scanning Interferometry, National Physical Laboratory, issue.116, p.131, 2010.

C. Y. Poon and B. Bhushan, Comparison of surface roughness measurements by stylus profiler, AFM and non-contact optical profiler, Wear, vol.190, issue.1, pp.76-88, 1995.

G. Binnig, C. F. Quate, and C. Gerber, Atomic Force Microscope, Physical Review Letters, vol.56, issue.9, pp.930-933, 1986.

D. Ricci and P. C. Braga, Recognizing and Avoiding Artifacts in AFM Imaging, vol.242, pp.25-38, 2003.

R. Hiesgen, S. Sörgel, and R. Costa, AFM as an analysis tool for high-capacity sulfur cathodes for Li-S batteries, Beilstein Journal of Nanotechnology, pp.611-635, 2013.

T. H. Kauffmann, Étude métrologique de solutions ioniques par spectrométrie Raman et analyses statistiques, 2016.

D. Lambert, Apport de la spectroscopie Raman dans l'analyse de peintures automobiles -Etude de comparabilité inter-laboratoires et combinaison de données spectroscopiques, 2017.

, Fiche toxicologique n°25 -Ethylène-glycol, 2016.

R. Deltombe, K. J. Kubiak, and M. Bigerelle, How to select the most relevant 3D roughness parameters of a surface: Relevance of 3D roughness parameters, Scanning, vol.36, issue.1, pp.150-60, 2014.

F. Blateyron, Etats de surface : la norme, 2006.

F. Magnoni, A. Rannée, and L. Marasinghe, Correlation between the scratch resistance of UV-cured PUA-based coatings and the structure and functionality of reactive diluents, Progress in Organic Coatings, vol.124, pp.193-202, 2018.

A. Mazkewitsch and A. Jaworski, Adhesion between polymers and concrete / Adhésion entre polymères et béton: Bonding · Protection · Repair / Revêtement · Protection · Réparation, pp.67-72, 1986.

Ç. M. Oral and B. Ercan, Influence of pH on morphology, size and polymorph of room temperature synthesized calcium carbonate particles, Powder Technology, vol.339, pp.781-789, 2018.

R. Shahsavari and S. H. Hwang, Morphogenesis of Cement Hydrate: From Natural C-S-H to Synthetic C-S-H, Cement Based Materials, 2018.

T. Hassenkam, L. L. Skovbjerg, and S. L. Stipp, Probing the intrinsically oil-wet surfaces of pores in North Sea chalk at subpore resolution, Proceedings of the National Academy of Sciences, vol.106, issue.15, pp.6071-6077, 2009.

J. Marteau, Caractérisation multi-échelle et analyse par essai d'indentation instrumentée de matériaux à gradient générés par procédés mécanioques et thermochimiques de traitement de surface, 2013.

A. E. Giannakopoulos and S. Suresh, Indentation of solids with gradients in elastic properties: Part II. axisymmetric indentors, International Journal of Solids and Structures, vol.34, issue.19, pp.2393-428, 1997.

, Fiche toxicologique n°3 -Acétone, 2018.

C. Chadfeau, S. H. Mohseni, S. Omary, V. Steiner, E. Belhaj et al., Influence d'un bioadjuvant sur l'adhésion du ciment sur parois coffrantes et évaluation de l'effet de la rugosité des parois coffrantes, Matériaux & Techniques, PUBLICATION ET COMMUNICATIONS Publication dans revue nationale avec comité de lecture ? 2019

-. Chadfeau, S. Omary, E. Belhaj, C. Fond, and F. Feugeas, 3rd International Conference on Bio-Based Building Materials

-. Chadfeau, S. Omary, E. Belhaj, C. Fond, F. Feugeas et al., Influence d'un bioadjuvant sur l'adhésion béton-coffrage, XVe Forum Jeunes Chercheurs, Commission Biodétérioration des Matériaux, Champs-sur-Marne, Ifsttar, 14 mai 2019. Résumé, poster et présentation orale, Caractérisation multiéchelle morphologique et chimique des surfaces cimentaires hydratées à 24 heures. Conférence MATERIAUX 2018, Fédération Française des Matériaux, 2017.

;. C. Résumé, E. Chadfeau, C. Belhaj, F. Fond, and . Feugeas, Caractérisation de la surface de coffrage par microscopie interférométrique, p.35

, Distinction : 1er prix. ? 2017 -Journée Portes Ouvertes de l'INSA de Strasbourg, 4 février 2017. ? 2017 -Journée Poster Ecole Doctorale MSII, 9 octobre 2017. ? 2017 -XIVe Forum Jeunes Chercheurs, vol.23, 2017.

, Communications de projet FUI ERGOFORM ? 2016 -2020 : 14 réunions d'avancement de projet FUI ERGOFORM ? 2017 -2020 : 4 réunions plénières de projet FUI ERGOFORM