P. Albertelli, A. Keshari, and A. Matta, Energy oriented multi cutting parameter optimization in face milling, Journal of cleaner production, vol.137, pp.1602-1618, 2016.

B. Amel, Contribution à l'étude du comportement dynamique d'une machine outil en présence des suspensions magnétiques, 2015.

I. O. Avram, Machine tool use phase: Modeling and analysis with environmental considerations (Doctoral dissertation, Verlag nicht ermittelbar), 2010.

O. I. Avram and P. Xirouchakis, Evaluating the use phase energy requirements of a machine tool system, Journal of Cleaner Production, vol.19, issue.6-7, pp.699-711, 2011.

V. A. Balogun, I. F. Edem, A. A. Adekunle, and P. T. Mativenga, Specific energy based evaluation of machining efficiency, Journal of Cleaner Production, 2016.

V. A. Balogun and P. T. Mativenga, Impact of undeformed chip thickness on specific energy in mechanical machining processes, J. Clean. Prod, vol.69, pp.260-268, 2014.

A. Bhattacharya, S. Das, P. Majumber, and A. Batish, Estimating the effect of cutting parameters on surface finish and power consumption during high speed machining of AISI 1045 steel using Taguchi design and ANOVA, Prod. Eng. Res. Dev, vol.3, pp.31-40, 2009.

R. K. Bhushan, Optimization of cutting parameters for minimizing power consumption and maximizing tool life during machining of Al alloy SiC particle composites, J Clean Prod, vol.39, pp.242-54, 2013.

E. Budak, Analytical models for high performance milling. Part I: Cutting forces, structural deformations and tolerance integrity, International Journal of Machine Tools and Manufacture, vol.46, pp.1478-1488, 2006.

M. L. Calvanese, P. Albertelli, A. Matta, and M. Taisch, Analysis of energy consumption in CNC machining centers and determination of optimal cutting conditions, pp.227-232, 2013.

D. Kordonowy, A power assessment of machining tools, 2002.

J. Dahmus and T. Gutowski, An Environmental Analysis of Machining, Proceedings of the, ASME International Mechanical Engineering Congress and RD&D Exposition, p.90, 2004.

Z. Deng, H. Zhang, Y. Fu, L. Wan, and W. Liu, Optimization of process parameters for minimum energy consumption based on cutting specific energy consumption, Journal of Cleaner Production, vol.166, pp.1407-1414, 2017.

T. Devoldere, W. Dewulf, W. Deprez, B. Willems, and R. J. Duou, Improvement Potentials for Energy Consumption in Disrecte Part Production Machines, Proceedings of the 14th CIRP Conference on Life Cycle Engineering, pp.311-316, 2007.

N. Diaz, E. Redelsheimer, and D. Dornfeld, Energy consumption characterization and reduction strategies for milling machine tool use, pp.263-267, 2011.

F. Draganescu, M. Gheorghe, and C. V. Doicin, Models of machine tool efficiency and specific consumed energy, J. Mater', Process. Tech, vol.141, issue.1, pp.9-15, 2003.

I. F. Edem and P. T. Mativenga, Modelling of energy demand from computer numerical control (CNC) toolpaths, Journal of cleaner production, vol.157, pp.310-321, 2017.

I. F. Edem and P. T. Mativenga, Impact of feed axis on electrical energy demand in mechanical machining processes, Journal of Cleaner Production, vol.137, pp.230-240, 2016.

Y. S. Guo, J. Loenders, J. Duou, and B. Lauwers, Optimization of energy consumption and surface quality in nish turning, Procedia CIRP, vol.1, issue.1, pp.512-517, 2012.

T. Gutowski, J. Dahmus, and S. Dalquist, Measuring the Environmental Load of Manufacturing Processes, Proceedings of International Society for Industrial Ecology (ISIE), 1215.

T. Gutowski, J. Dahmus, and A. Thiriez, Electrical energy requirements for manufacturing processes, 13th CIRP international conference on life cycle engineering, vol.31, 2006.

I. Hanafi, A. Khamlichi, F. Mata-cabrera, E. Almansa, and A. Jabbouri, Optimization of cutting conditions for sustainable machining of PEEK-CF30 using TiNntools, J. Clean. Prod, vol.33, pp.1-9, 2012.

Y. He, F. Liu, T. Wu, F. P. Zhong, and B. Peng, Analysis and estimation of energy consumption for numerical control machining, Proceedings of the Institution of Mechanical Engineers, vol.226, issue.2, pp.255-266, 2012.

T. Hentati, M. Barkallah, S. Bouaziz, and M. Haddar, Dynamic modeling of spindlerolling bearings systems in peripheral milling operations, Journal of Vibroengineering, vol.18, issue.3, 1982.

T. Herzog, Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles), World Greenhouse Gas Emissions: 2005. World Resources Institute, 2007.

H. Hassine, Modélisation, simulation et optimisation pour l'eco-fabrication. (thése), 2015.

T. Holkup, H. Cao, P. Kolá?, Y. Altintas, and J. Zelený, Thermo-mechanical model of spindles, CIRP annals, vol.59, issue.1, pp.365-368, 2010.

D. Y. Jang, J. Jung, and J. Seok, Modeling and parameter optimization for cutting energy reduction in MQL milling process, International Journal of Precision Engineering and Manufacturing-Green Technology, vol.3, issue.1, pp.5-12, 2016.

S. Klancnik, M. Brezocnik, J. Balic, and I. Karabegovic, Programming of CNC milling machines using particle swarm optimization, Mater Manuf Process, vol.28, issue.7, pp.811-815, 2012.

A. Kulkarni, H. Mandave, and V. Sabnis, Optimization of power consumption for CNC turning Of AISI 1040 steel using Taguchi approach, Int J Innov Res Sci Eng Technol, vol.3, issue.8, pp.15383-15390, 2014.

W. Li and W. Kara, An empirical model for predicting energy consumption ofmanufacturing processes: a case of turning process, Proceedings of the Institution of Mechanical Engineers, vol.225, issue.9, pp.1636-1646, 2011.

C. Li, Selection of optimum parameters in multi-pass face milling for maximum energy efficiency and minimum production cost, Journal of Cleaner Production, vol.140, pp.1805-1818, 2017.

J. Li, Y. Lu, H. Zhao, P. Li, and Y. Yao, Optimization of cutting parameters for energy saving, Int J Adv Manuf Technol, vol.70, pp.117-124, 2014.

X. Luan, S. Zhang, and G. Cai, Optimal Cutting Parameters to Reduce Power Consumption in Face Milling of a Cast Iron Alloy for Environmental Sustainability, Sustainable Design and Manufacturing, pp.135-148, 2016.

J. Lv, R. Tang, S. Jia, and Y. Liu, Experimental study on energy consumption of computer numerical control machine tools, Journal of Cleaner Production, vol.112, pp.3864-3874, 2016.

M. F. Rajemi, Sustainable machining : selection of optimum turning conditions based on minimum energy considerations, Journal of Cleaner Production, vol.18, p.10591065, 2010.

P. T. Mativenga and M. F. Rajemi, Calculation of optimum cutting parameters based on minimum energy footprint, CIRP Annals -Manufacturing Technology, vol.60, issue.1, pp.149-152, 2011.

R. Neugebauer, M. Wabner, H. Rentzsch, and S. Ihlenfeldt, Structure principles of energy efficient machine tools, CIRP Journal of Manufacturing Science and Technology, vol.4, issue.2, pp.136-147, 2011.

G. Quintana, J. Ciurana, and J. Ribatallada, Modelling power consumption in ballend milling operations

, Mater Manuf Process, vol.26, pp.746-56, 2011.

M. Rief, B. Karpuschewski, and E. Kalhöfer, Evaluation and modeling of the energy demand during machining, CIRP Journal of Manufacturing Science and Technology, vol.19, pp.62-71, 2017.

A. R. Rodrigues and R. T. Coelho, Influence of the tool edge geometry on specific cutting energy at high-speed cutting, J. Braz. Soc. Mech. Sci. Eng, vol.29, issue.3, 2007.

S. Sushrut and . Pavanaskar, Improving Energy E-ciency in CNC Machining, 2014.

H. Taissir and . Fki, Contribution à l'étude dynamique d'un palier à roulement en présance de défaut, p.thése, 2008.

V. A. Balogun and M. , Modelling of direct energy requirements in mechanical machining processes, Journal of Cleaner Production, vol.41, pp.179-186, 2013.

Q. Wang, F. Liu, and X. Wang, Multi-objective optimization of machining parameters considering energy consumption, The International Journal of Advanced Manufacturing Technology, vol.71, pp.1133-1142, 2014.

Z. Wang, J. Yuan, Z. Yin, and C. Li, Study on high-speed cutting parameters optimization of AlMn1Cu based on neural network and genetic algorithm, Advances in Mechanical Engineering, vol.8, issue.4, p.1687814016644126, 2016.

H. S. Yoon, J. Y. Lee, and M. S. Kim, Empirical power consumption model for material removal in three-axis milling, Journal of Cleaner Production, vol.78, pp.54-62, 2014.

H. S. Yoon, J. S. Moon, M. Q. Pham, G. B. Lee, and S. H. Ahn, Control of machining parameters for energy and cost savings in micro-scale drilling of PCBs, J. Clean. Prod, vol.54, pp.41-48, 2013.

Q. Zhong, R. Tang, and T. Peng, Decision rules for energy consumption minimization during material removal process in turning, Journal of Cleaner Production, vol.140, pp.1819-1827, 2017.

L. Zhou, J. Li, F. Li, Q. Meng, J. Li et al., Energy consumption model and energy efficiency of machine tools: a comprehensive literature review, J Clean Prod, vol.112, pp.3721-3755, 2016.

, Liste des publications et communications

B. Anoire, A. Jdidia, . Bellacico, H. Taissir, B. Maher et al., Consumed energy modelization of an axis feed system in case of sustainable manufacturing

B. Anoire, . Jdidia, H. Taissir, A. Bellacico, M. Taoufik et al., Consumed energy by a bearing supported spindle in presence of dynamic cutting force and defects

B. Anoire, A. Jdidia, . Bellacico, B. Maher, and H. Hichem,

K. Taoufik, R. Alain, and H. Mohamed, Analytical method for the calculation of tool machine energy consumption, The International Congress Design and Modelling of Mechanical Systems (CMSM'2017) 27th -29th, 2017.

B. Anoire, . Jdidia, H. Taissir, A. Bellacico, M. Taoufik et al., Influence of the milling cutting force dynamic behavior and some parts weight on axis feed power consumption, 2018.

B. Anoire, . Jdidia, H. Taissir, A. Bellacico, M. Taoufik et al., Optimizing cutting conditions in single pass face milling for minimum cutting energy, time, cost, and surface roughness, 2018.