L. Toussaint, N. Lebaal, D. Schlegel, and S. Et-gomes, Automatic optimization of air duct design using experimental data and numerical results, International Journal of Simulation, 2010.

L. Toussaint, F. Demoly, N. Lebaal, and S. Et-gomes, PLM-based Approach for Design Verification and Validation using Manufacturing Process Knowledge, Journal of Systemics, Cybernetics and Informatics, vol.8, issue.1, pp.1-7, 2010.

. Communications-avec-comité-de-lecture, L. Internationales-toussaint, S. Gomes, and J. C. Et-sagot, Using a Process Knowledge Based CAD for a More Robust Response to Demands for Quotation, 19th CIRP Design Conference - Competitive Design, 2008.

L. Toussaint, S. Gomes, and J. C. Et-sagot, Process Knowledge-Based CAD Verification for a more Robust First Concept Reponse. 2nd International Multi-Conference on Engineering and Technological Innovation IMETI, 2009.

L. Toussaint, S. Gomes, D. Monticolo, and N. Et-lebaal, Knowledge Management and DFM - Future work on Design Optimization for Extrusion Blow Molding. Workshop CoDeKF'09 ? Collaborative Design and Knowledge Factory, 2009.

L. Toussaint, J. B. Bluntzer, S. Gomes, and J. C. Et-sagot, Utilisation d'une CAO à base de connaissances process pour une meilleure robustesse de réponses à consultation, 15ème Séminaire CONFERE (Collège d'Études et de Recherches en Design et Conception de Produits) sur l'Innovation et la Conception, 2008.

L. Toussaint, N. Lebaal, and S. Et-gomes, Management des connaissances et DFM : Optimisation de la conception de conduits d'admission d'air en avant phase pour l'extrusion soufflage, GDR MACS Journées Sciences et Techniques de la Production de Biens et de Services, pp.18-19, 2010.

L. Toussaint, La boucle conception-optimisation-validation : ingénierie de connaissances pour une CAO 4D, GDR MACS Journées Sciences et Techniques de la Production de Biens et de Services, 2008.

H. S. Abdalla, Concurrent engineering for global manufacturing, International Journal of Production Economics, vol.60, issue.61, pp.251-260, 1999.
DOI : 10.1016/S0925-5273(98)00152-2

B. Agard, Contribution a une méthodologie de conception de produits à forte diversité, 2002.

G. Laboratoire, Gestion Industrielle Logistique et COnception'. Grenoble, Institut National Polytechnique De Grenoble, Thèse de Doctorat

M. Aldanondo and E. Et-vareilles, Configuration for mass customization: how to extend product configuration towards requirements and process configuration, Journal of Intelligent Manufacturing, vol.12, issue.4, pp.521-535, 2008.
DOI : 10.1007/s10845-008-0135-z

M. Aldanondo, E. Vareilles, K. Hadj-hamou, and P. Et-gaborit, A constraint based approach for aiding heat treatment operation design and distortion evaluation, Artificial Intelligence Applications and Innovations. I. Maglogiannis, K. Karpouzis et M. Bramer, vol.204, pp.254-261, 2006.
DOI : 10.1007/0-387-34224-9_30
URL : https://hal.archives-ouvertes.fr/hal-00453011

N. Aleixos, P. Company, and M. Et-contero, Integrated modeling with top-down approach in subsidiary industries, Computers in Industry, vol.53, issue.1, pp.97-116, 2004.
DOI : 10.1016/S0166-3615(03)00122-2

F. Ameri and D. Et-dutta, Product Lifecycle Management: Closing the Knowledge Loops, Computer-Aided Design and Applications, vol.36, issue.3, pp.577-590, 2005.
DOI : 10.1080/16864360.2005.10738322

A. Liou, A. Wu, and M. , Mapping knowledge to rules for scheduling expert systems, Expert Systems with Applications, vol.10, pp.3-4, 1996.

K. R. Apt, The essence of constraint propagation, Theoretical Computer Science, vol.221, issue.1-2, pp.179-210, 1999.
DOI : 10.1016/S0304-3975(99)00032-8

S. Arimoto, T. Ohashi, M. Ikeda, S. Miyakawa, and M. Et-kiuchi, Development of Machining-Producibility Evaluation Method (MEM), CIRP Annals - Manufacturing Technology, vol.42, issue.1, pp.119-122, 1993.
DOI : 10.1016/S0007-8506(07)62406-8

M. F. Ashby, Y. J. Bréchet, D. Cebon, and L. Et-salvo, Selection strategies for materials and processes, Materials & Design, vol.25, issue.1, pp.51-67, 2004.
DOI : 10.1016/S0261-3069(03)00159-6

M. Auffret, Content Management Makes Sense -Part 2: Technical impact of semantics on content management, Journal of Knowledge Management Practice, 2001.

Y. Avramenko, A. Kraslawski, and W. Et-krysiak, Case-based reasoning tool for the support of process and product design, Computer Aided Chemical Engineering. P. Luis et E. Antonio, vol.20, pp.697-702, 2005.
DOI : 10.1016/S1570-7946(05)80238-X

E. Aziz and C. Et-chassapis, Knowledge-based Geometry Generation for Spur and Helical Gears, Concurrent Engineering, vol.10, issue.3, pp.251-261, 2002.
DOI : 10.1177/106329302761689160

Y. Baba and K. Et-nobeoka, Towards knowledge-based product development: the 3-D CAD model of knowledge creation, Research Policy, vol.26, issue.6, pp.643-659, 1998.
DOI : 10.1016/S0048-7333(97)00040-1

I. Babuska and J. Et-oden, Verification and validation in computational engineering and science: basic concepts, Computer Methods in Applied Mechanics and Engineering, vol.193, issue.36-38, pp.36-38, 2004.
DOI : 10.1016/j.cma.2004.03.002

J. Badin, N. Troussier, and S. Et-gomes, Vers de nouvelles méthodes et outils pour la simulation multi-physiques à base de connaissances métiers, MICADO Virtual PLM'09, 2009.

R. Bakerjian, R. R. Barton, Y. Joo, and I. Ham, Design for manufacturability, Society of manufacturing engineers Feedback of Manufacturing Experience for DFM Design Rules. CIRP Annals -Manufacturing Technology, pp.115-120, 1992.

H. A. Bashir and V. Et-thomson, Models for estimating design effort and time, Design Studies, vol.22, issue.2, pp.141-155, 2001.
DOI : 10.1016/S0142-694X(00)00014-4

D. Baxter, J. Gao, K. Case, J. Harding, B. Young et al., A framework to integrate design knowledge reuse and requirements management in engineering design, Robotics and Computer-Integrated Manufacturing, vol.24, issue.4, pp.585-593, 2008.
DOI : 10.1016/j.rcim.2007.07.010

M. Baxter, Product Design: Practical Methods for the Systematic Development of New Products, pp.978-0412632303, 1999.

S. Bekhti, DYPKM : Un processus dynamique de definition et de reutilisation de memoires de projets. Reseaux, Connaissances et Organisations, 2003.
URL : https://hal.archives-ouvertes.fr/tel-00511045

A. Bernard, Fabrication assistée par ordinateur, 2003.

H. Beyer and B. Et-sendhoff, Robust optimization ??? A comprehensive survey, Computer Methods in Applied Mechanics and Engineering, vol.196, issue.33-34, pp.33-34, 2007.
DOI : 10.1016/j.cma.2007.03.003

A. Bissay, Du déploiement d'un système PLM vers une intégration des connaissances, 2010.

. Laboratoire-d-', Informatique pour l'Entreprise et les Systèmes de Production, Thèse de Doctorat

F. Blondel, S. Edouard, and M. N. Et-el-mabrouki, Quelle articulation entre intelligence économique et knowledge management au sein de l'entreprise XV Conférence Internationale de Management Stratégique, 2006.

J. C. Bocquet, Ingénierie simultanée, conception intégrée. Conception de produits mécaniques, méthodes, modèles et outils. M. Tollenaere, Editions Hermès, pp.29-52, 1998.

P. T. Boggs and J. W. Et-tolle, Sequential Quadratic Programming, Acta Numerica, vol.1991, pp.1-51, 1995.
DOI : 10.1007/BF01580366

G. Boothroyd, Product design for manufacture and assembly, Computer-Aided Design, vol.26, issue.7, pp.505-520, 1994.
DOI : 10.1016/0010-4485(94)90082-5

G. Boothroyd and P. Et-radovanovic, Estimating the Cost of Machined Components During the Conceptual Design of a Product, CIRP Annals - Manufacturing Technology, vol.38, issue.1, pp.157-160, 1989.
DOI : 10.1016/S0007-8506(07)62674-2

J. F. Boujut, S. Tichkiewitch, and E. Et-blanco, Integration of Downstream Actors in the Design Process Using a Dedicated Expert CAD Tool for Forged Parts, Concurrent Engineering, vol.5, issue.4, pp.327-336, 1997.
DOI : 10.1177/1063293X9700500405

P. Bourdet and F. Et-villeneuve, La gamme automatique en usinage Groupe GAMA, 1990.
URL : https://hal.archives-ouvertes.fr/hal-00368141

J. S. Brown and P. Et-duguid, Organizational Learning and Communities-of-Practice: Toward a Unified View of Working, Learning, and Innovation, Organization Science, vol.2, issue.1, pp.40-57, 1991.
DOI : 10.1287/orsc.2.1.40

M. Callot, S. Kneebone, K. Oldham, A. Murton, and R. Et-brimble, MOKA -A methodology for developing knowledge based engineering applications. Forum 98 -Solutions for Informix Users, 1998.

A. Candlot, Principes d'assistance a la maitrise d'ouvrage pour la modelisation et l'integration d'expertise, Institut de Recherche en Communications et Cybernétique de Nantes Thèse de Doctorat, 2006.
URL : https://hal.archives-ouvertes.fr/tel-00429650

C. B. Chapman and M. Et-pinfold, The application of a knowledge based engineering approach to the rapid design and analysis of an automotive structure, Advances in Engineering Software, vol.32, issue.12, pp.903-912, 2001.
DOI : 10.1016/S0965-9978(01)00041-2

Y. Chen and J. Et-liu, Cost-effective design for injection molding, Robotics and Computer-Integrated Manufacturing, vol.15, issue.1, pp.1-21, 1999.
DOI : 10.1016/S0736-5845(99)00005-8

S. C. Chong and Y. S. Et-choi, Critical Factors In The Successful Implementation Of Knowledge Management, Journal of Knowledge Management Practice, 2005.

J. Ciurana, M. L. Garcia-romeu, I. Ferrer, and M. Et-casadesús, A model for integrating process planning and production planning and control in machining processes, Robotics and Computer-Integrated Manufacturing, vol.24, issue.4, pp.532-544, 2008.
DOI : 10.1016/j.rcim.2007.07.013

C. Coello, Theoretical and Numerical Constraitn-handling Techniques Used with Evolutionary Algorithms : A survey of the State of the Art, Computer Methods in Applied Mechanics and Engineering, vol.191, pp.11-12, 2002.

C. Coppens, Les outils KBE : une approche chez PSA Peugeot Citroën, 4th International Conference on Integrated Design and Manufacturing in Mechanical Engineering -IDMME 2002, 2002.

U. Cugini, G. Cascini, M. Muzzupappa, and V. Et-nigrelli, Integrated Computer-Aided Innovation: The PROSIT approach, Computers in Industry, vol.60, issue.8, pp.629-641, 2009.
DOI : 10.1016/j.compind.2009.05.014

D. E. Culler and W. Et-burd, A framework for extending computer aided process planning to include business activities and computer aided design and manufacturing (CAD/CAM) data retrieval, Robotics and Computer-Integrated Manufacturing, vol.23, issue.3, pp.339-350, 2007.
DOI : 10.1016/j.rcim.2006.02.005

P. F. Culverhouse, Constraining designers and their CAD tools, Design Studies, vol.16, issue.1, pp.81-101, 1995.
DOI : 10.1016/0142-694X(95)90648-Y

P. Cunningham and A. Et-bonzano, Knowledge engineering issues in developing a case-based reasoning application, Knowledge-Based Systems, vol.12, issue.7, pp.371-379, 1999.
DOI : 10.1016/S0950-7051(99)00042-8

R. Curran, G. Gomis, S. Castagne, J. Butterfield, T. Edgar et al., Integrated digital design for manufacture for reduced life cycle cost, International Journal of Production Economics, vol.109, issue.1-2, pp.27-40, 2007.
DOI : 10.1016/j.ijpe.2006.11.010

W. Currie, A knowledge-based risk assessment framework for evaluating web-enabled application outsourcing projects, International Journal of Project Management, vol.21, issue.3, pp.207-217, 2003.
DOI : 10.1016/S0263-7863(02)00095-9

F. Danesi, N. Gardan, Y. Gardan, and M. Et-reimeringer, P4LM: A methodology for product lifecycle management, Computers in Industry, vol.59, issue.2-3, pp.304-317, 2008.
DOI : 10.1016/j.compind.2007.06.013

D. Das, S. K. Gupta, and D. S. Et-nau, Generating redesign suggestions to reduce setup cost: a step towards automated redesign, Computer-Aided Design, vol.28, issue.10, pp.763-782, 1996.
DOI : 10.1016/0010-4485(95)00034-8

K. Deb, Multi-Objective Optimization Using Evolutionary Algorithms, pp.978-0471873396, 2001.

E. Deciu, E. Ostrosi, M. Ferney, and M. Et-gheorghe, Configurable product design using multiple fuzzy models, Journal of Engineering Design, vol.42, issue.2, pp.209-233, 2005.
DOI : 10.1016/S0019-9958(65)90241-X

F. Demoly, Conception intégrée et gestion d'informations techniques : application à l'ingénierie du produit et de sa séquence d'assemblage. Laboratoire Mécatronique, Modèles, Méthodes et Métiers -M3M, 2010.

F. Demoly, D. Monticolo, B. Eynard, L. Rivest, and S. Et-gomes, Multiple viewpoint modelling framework enabling integrated product???process design, International Journal on Interactive Design and Manufacturing (IJIDeM), vol.2, issue.1, pp.12008-12018, 2010.
DOI : 10.1007/s12008-010-0107-3

F. Demoly, X. Yan, B. Eynard, L. Rivest, and S. Et-gomes, An assembly oriented design framework for product structure engineering and assembly sequence planning, Robotics and Computer-Integrated Manufacturing, vol.27, issue.1, 2010.
DOI : 10.1016/j.rcim.2010.05.010

D. Deneux, Méthodes et modèles pour la conception concourante, 2002.

Q. Deng and D. Et-yu, An Approach To Integrating Knowledge Management Into The Product Development Process, Journal of Knowledge Management Practice, vol.7, issue.2, 2006.

W. Derigent, Méthodologie de passage d'un modèle CAO vers un modèle FAO pour des pièces aéronautiques : Prototype logiciel dans le cadre du projet USIQUICK. CRAN -Centre de recherche en automatique de Nancy, Thèse de Doctorat, 2005.

P. Dewhurst and G. Et-boothroyd, Early cost estimating in product design, Journal of Manufacturing Systems, vol.7, issue.3, pp.183-191, 1988.
DOI : 10.1016/0278-6125(88)90003-9

G. Ducellier, Gestion de règles expertes en ingénierie collaborative : application aux plateformes PLM, Laboratoire des Systèmes Mécaniques et d'Ingénierie Simultanée. Troyes, 2008.

J. R. Duflou, J. Váncza, and R. Et-aerens, Computer aided process planning for sheet metal bending: A state of the art, Computers in Industry, vol.56, issue.7, pp.747-771, 2005.
DOI : 10.1016/j.compind.2005.04.001

G. Tools and . Llc, Least Squares Fitting of Data, 2008.

F. Elgh, Supporting management and maintenance of manufacturing knowledge in design automation systems, Advanced Engineering Informatics, vol.22, issue.4, pp.445-456, 2008.
DOI : 10.1016/j.aei.2008.05.004

H. Elmaraghy, A. Azab, G. Schuh, and C. Et-pulz, Managing variations in products, processes and manufacturing systems, CIRP Annals - Manufacturing Technology, vol.58, issue.1, pp.441-446, 2009.
DOI : 10.1016/j.cirp.2009.04.001

J. Ermine, La Gestion des Connaissances, un levier stràtegique pour les entreprises, 2000.

J. Ermine, La gestion de connaissances, Hermès Sciences publications, 2002.

A. Etienne, Intégration Produit / Process par les concepts d'activités et de caractéristiques clés -Application à l'optimisation de l'allocation des tolérances géométriques, Laboratoire de Génie Industriel et de Production Mécanique Thèse de Doctorat, 2007.

B. Eynard, Gestion du cycle de vie des produits et dynamique des connaissances industrielles en conception intégrée, Laboratoire des Systèmes Mécaniques et d'Ingénierie Simultanée. Troyes, 2005.

B. Eynard, T. Gallet, P. Nowak, and L. Et-roucoules, UML based specifications of PDM product structure and workflow, Computers in Industry, vol.55, issue.3, pp.301-316, 2004.
DOI : 10.1016/j.compind.2004.08.006

B. Eynard, M. Lombard, N. Matta, and J. Et-renaud, Gestion Dynamique des Connaissances Industrielles, Revue Francaise de Gestion Industrielle, vol.24, issue.1, pp.129-130, 2005.
URL : https://hal.archives-ouvertes.fr/hal-00288957

A. Fall, S. Gomes, and J. C. Et-sagot, An organizational change management experiment integrating Computer Supported Cooperative Work (CSCW) Systems, 12th International Conference on Management of Technology: IAMOT, 2003.

M. Farenzena and A. Et-fusiello, Stabilizing 3D modeling with geometric constraints propagation, Computer Vision and Image Understanding, vol.113, issue.11, pp.1147-1157, 2009.
DOI : 10.1016/j.cviu.2009.05.004

C. Feng and A. Et-kusiak, Constraint-based design of parts, Computer-Aided Design, vol.27, issue.5, pp.343-352, 1995.
DOI : 10.1016/0010-4485(95)96798-Q

I. Ferrer, J. Rios, and J. Et-ciurana, An approach to integrate manufacturing process information in part design phases, Journal of Materials Processing Technology, vol.209, issue.4, pp.2085-2091, 2009.
DOI : 10.1016/j.jmatprotec.2008.05.009

S. K. Fixson, Modularity and Commonality Research: Past Developments and Future Opportunities, Concurrent Engineering, vol.15, issue.2, pp.85-111, 2007.
DOI : 10.1177/1063293X07078935

K. Forsberg and H. Et-mooz, The Relationship of System Engineering to the Project Cycle, National Council for Systems Engineering (NCOSE), 1991.

J. M. Fouet, Connaissances et savoir-faire en entreprise, intégration et capitalisation, 1997.

M. Fu, The application of surface demoldability and moldability to side-core design in die and mold CAD, Computer-Aided Design, vol.40, issue.5, pp.567-575, 2008.
DOI : 10.1016/j.cad.2008.02.002

M. W. Fu, A. Y. Nee, and J. Y. Et-fuh, The application of surface visibility and moldability to parting line generation, Computer-Aided Design, vol.34, issue.6, pp.469-480, 2002.
DOI : 10.1016/S0010-4485(01)00117-8

Y. Fu and R. Et-shen, GA based CBR approach in Q&A system, Expert Systems with Applications, vol.26, issue.2, pp.167-170, 2004.
DOI : 10.1016/S0957-4174(03)00117-9

F. Fuxin, Configurable product views based on geometry user requirements, Computer-Aided Design, vol.37, issue.9, pp.957-966, 2005.
DOI : 10.1016/j.cad.2004.09.022

J. X. Gao, A. Hayder, P. G. Maropoulos, and W. Et-cheung, Application of product data management technologies for enterprise integration, International Journal of Computer Integrated Manufacturing, vol.16, issue.7-8, pp.7-8, 2003.
DOI : 10.1080/0951192031000115813

J. X. Gao, Y. S. Tang, and R. Sharma, A feature model editor and process planning system for sheet metal products, Journal of Materials Processing Technology, vol.107, issue.1-3, pp.1-3, 2000.
DOI : 10.1016/S0924-0136(00)00670-1

G. Lorenzo, M. M. Et-bello-pérez, and R. E. , A model and its different applications to case-based reasoning, Knowledge-Based Systems, vol.9, issue.7, pp.465-473, 1996.
DOI : 10.1016/S0950-7051(96)01058-1

N. Gardan and Y. Et-gardan, An application of knowledge based modelling using scripts, Expert Systems with Applications, vol.25, issue.4, pp.555-568, 2003.
DOI : 10.1016/S0957-4174(03)00096-4

Y. Gardan, M. Hillereau, and E. Et-perrin, CAD Interactions for Increasing Designers Awareness of Manufacturability, Leading the Web in Concurrent Engineering: Next Generation Concurrent Engineering, pp.568-575, 2006.

M. R. Gholamian and S. M. Et-ghomi, Meta knowledge of intelligent manufacturing: An overview of state-of-the-art, Applied Soft Computing, vol.7, issue.1, pp.1-16, 2007.
DOI : 10.1016/j.asoc.2004.12.008

W. Gielingh, An assessment of the current state of product data technologies, Computer-Aided Design, vol.40, issue.7, pp.750-759, 2008.
DOI : 10.1016/j.cad.2008.06.003

S. Gomes, Ingénierie à base de connaissances pour une conception, productive, optimisée, collaborative et innovante du système Projet-Produit-Process-Usage, 2008.

S. Gomes and J. C. Et-sagot, A concurrent engineering experience based on a cooperative and objective oriented design methodology, 3rd International Conference on Integrated Design and Manufacturing in Mechanical Engineering, 2002.

S. Gomes, J. C. Sagot, A. Koukam, and N. Leroy, ACSP an intranet forum supporting a concurrent engineering design life cycle, 6th Concurrent Engineering Conference ECEC'99, 1999.

S. Gomes and P. Et-serrafero, Ingénierie collaborative et management des connaissances industrielles : du modèle systémique multivues au modèle positiviste Knova, Gestion Dynamique des Connaissances Industrielles. B. Eynard, M. Lombard, N. Matta et J. Renaud, pp.181-196, 2004.

S. Gomes, P. Serrafero, D. Monticolo, and B. Et-eynard, Extracting engineering knowledge from PLM Systems: An experimental approach, International Conference on Product Lifecycle Management PLM'05, 2005.

C. Grabowik, K. Kalinowski, and Z. Et-monica, Integration of the CAD/CAPP/PPC systems, Journal of Materials Processing Technology, vol.164, issue.165, pp.1358-1368, 2005.
DOI : 10.1016/j.jmatprotec.2005.02.036

S. Grewal, An Integrated Approach to Manufacturing Process Design and Costing, Concurrent Engineering, vol.13, issue.3, pp.199-207, 2005.
DOI : 10.1177/1063293X05056474

M. Grundstein, Reperer et mettre en valeur les connaissances cruciales pour l'entreprise. 10ème Congrès International de l'AFAV, 2000.

M. U. Grundstein, . Cadre, . Pour, . Les, and . Cruciales-pour-l-'entreprise, GAMETH®, p.29, 2007.

M. Gupta and K. Galloway, Activity-based costing/management and its implications for operations management, Technovation, vol.23, issue.2, pp.131-138, 2003.
DOI : 10.1016/S0166-4972(01)00093-1

S. K. Gupta and D. S. Et-nau, A systematic approach for analyzing the manufacturability of Machined parts, Computer Aided Design, vol.2, issue.5, pp.323-342, 1995.

S. K. Gupta, W. C. Regli, D. Das, and D. S. Et-nau, Automated manufacturability analysis: A survey, Research in Engineering Design, vol.41, issue.5, pp.168-190, 1997.
DOI : 10.1007/BF01596601

G. Harhalakis, A. Kinsey, I. Minis, and H. Et-rathbun, Manufacturability evaluation of electronic products using group technology. NSF design and manufacturing systems grantees, 1993.

M. Hauschild, J. Jeswiet, and L. Et-alting, From Life Cycle Assessment to Sustainable Production: Status and Perspectives, CIRP Annals - Manufacturing Technology, vol.54, issue.2, pp.1-21, 2005.
DOI : 10.1016/S0007-8506(07)60017-1

S. S. Heragu, Facilities Design, 2008.

O. Herbeaux and A. Et-mille, ACCELERE: a case-based design assistant for closed cell rubber industry, Knowledge-Based Systems, vol.12, pp.5-6, 1999.

K. P. Hew, N. Fisher, and H. B. Et-awbi, Towards an integrated set of design tools based on a common data format for building and services design, Automation in Construction, vol.10, issue.4, pp.459-476, 2001.
DOI : 10.1016/S0926-5805(00)00082-0

K. S. Hindi and K. Et-fleszar, A constraint propagation heuristic for the single-hoist, multiple-products scheduling problem, Computers & Industrial Engineering, vol.47, issue.1, pp.91-101, 2004.
DOI : 10.1016/j.cie.2004.03.002

R. Holt and C. Et-barnes, Towards an integrated approach to ???Design for X???: an agenda for decision-based DFX research, Research in Engineering Design, vol.3, issue.2, pp.123-136, 2009.
DOI : 10.1007/s00163-009-0081-6

G. Q. Huang and K. L. Et-mak, The DFX shell: A generic framework for developing design for X tools, Robotics and Computer-Integrated Manufacturing, vol.13, issue.3, pp.271-280, 1997.
DOI : 10.1016/S0736-5845(97)00006-9

G. Q. Huang, J. Shi, and K. L. Et-mak, Synchronized system for ???Design for X??? guidelines over the WWW, Journal of Materials Processing Technology, vol.107, issue.1-3, pp.1-3, 2000.
DOI : 10.1016/S0924-0136(00)00702-0

V. Hubka and W. E. Et-eder, Theory of technical systems: A total concept theory for engineering design (2nd revised and enlarged edition), 1988.
DOI : 10.1007/978-3-642-52121-8

R. Hunter-alarcón, R. Chueco, J. , P. García, J. M. Et-vizán-idoipe et al., Fixture knowledge model development and implementation based on a functional design approach, Robotics and Computer-Integrated Manufacturing, vol.26, issue.1, pp.56-66, 2010.
DOI : 10.1016/j.rcim.2009.02.001

C. Y. Ip and W. C. Et-regli, A 3D object classifier for discriminating manufacturing processes, Computers & Graphics, vol.30, issue.6, pp.903-916, 2006.
DOI : 10.1016/j.cag.2006.08.013

K. Ishii, C. H. Lee, and R. A. Et-miller, Methods for Process Selection in Design, ASME Design Theory and Methodology Conference, 1990.

N. Iyer, S. Jayanti, K. Lou, Y. Kalyanaraman, and K. Et-ramani, Three-dimensional shape searching: state-of-the-art review and future trends, Computer-Aided Design, vol.37, issue.5, pp.509-530, 2005.
DOI : 10.1016/j.cad.2004.07.002

H. S. Jagdev and J. Et-browne, The extended enterprise-a context for manufacturing, Production Planning & Control, vol.9, issue.3, pp.216-229, 1998.
DOI : 10.1080/095372898234190

R. Jans, Z. Degraeve, and L. Et-schepens, Analysis of an industrial component commonality problem, European Journal of Operational Research, vol.186, issue.2, pp.801-811, 2008.
DOI : 10.1016/j.ejor.2007.01.008

N. Janthong, D. Brissaud, and S. Et-butdee, Combining axiomatic design and case-based reasoning in an innovative design methodology of mechatronics products, CIRP Journal of Manufacturing Science and Technology, vol.2, issue.4, 2010.
DOI : 10.1016/j.cirpj.2010.05.005

J. Jarmulak, E. J. Kerckhoffs, and P. Et-van-'t-veen, Case-based reasoning for interpretation of data from non-destructive testing, Engineering Applications of Artificial Intelligence, vol.14, issue.4, pp.401-417, 2001.
DOI : 10.1016/S0952-1976(01)00026-4

Y. Jiang, J. Chen, and X. Et-ruan, Fuzzy similarity-based rough set method for case-based reasoning and its application in tool selection, International Journal of Machine Tools and Manufacture, vol.46, issue.2, pp.107-113, 2006.
DOI : 10.1016/j.ijmachtools.2005.05.003

Y. Jianjun, J. Baiyang, G. Yifeng, D. Jinxiang, and L. Et-chenggang, Research on evaluation methodologies of product life cycle engineering design (LCED) and development of its tools, International Journal of Computer Integrated Manufacturing, vol.5, issue.8, pp.923-942, 2008.
DOI : 10.1007/s00170-002-1527-4

S. Jung, T. Lim, and D. Kim, Integrating radial basis function networks with case-based reasoning for product design, Expert Systems with Applications, vol.36, issue.3, pp.5695-5701, 2009.
DOI : 10.1016/j.eswa.2008.06.099

M. Kadidal and B. Et-bidanda, A castability expert system, Computers & Industrial Engineering, vol.25, issue.1-4, pp.99-102, 1993.
DOI : 10.1016/0360-8352(93)90230-U

O. Kerbrat, P. Mognol, and J. Y. Et-hascoet, Manufacturing complexity evaluation at the design stage for both machining and layered manufacturing, CIRP Journal of Manufacturing Science and Technology, vol.2, issue.3, pp.208-215, 2010.
DOI : 10.1016/j.cirpj.2010.03.007
URL : https://hal.archives-ouvertes.fr/hal-00522092

K. Kim and D. Et-chhajed, Commonality in product design: Cost saving, valuation change and cannibalization, European Journal of Operational Research, vol.125, issue.3, pp.602-621, 2000.
DOI : 10.1016/S0377-2217(99)00271-4

F. Kimura, H. Ariyoshi, H. Ishikawa, Y. Naruko, and H. Et-yamato, Capturing Expert Knowledge for Supporting Design and Manufacturing of Injection Molds. CIRP Annals - Manufacturing Technology, pp.147-150, 2004.

H. Komoto and T. Et-tomiyama, Integration of a service CAD and a life cycle simulator, CIRP Annals - Manufacturing Technology, vol.57, issue.1, pp.9-12, 2008.
DOI : 10.1016/j.cirp.2008.03.001

B. Koo and M. Et-fischer, Feasibility Study of 4D CAD in Commercial Construction, Journal of Construction Engineering and Management, vol.126, issue.4, 1998.
DOI : 10.1061/(ASCE)0733-9364(2000)126:4(251)

O. Kulak, S. Cebi, and C. Et-kahraman, Applications of axiomatic design principles: A literature review, Expert Systems with Applications, vol.37, issue.9, pp.6705-6717, 2010.
DOI : 10.1016/j.eswa.2010.03.061

J. Kulon, D. Mynors, and P. Et-broomhead, A knowledge-based engineering design tool for metal forging, Journal of Materials Processing Technology, vol.177, issue.1-3, pp.1-3, 2006.
DOI : 10.1016/j.jmatprotec.2006.04.062

S. Kumar, R. Singh, and G. S. Et-sekhon, CCKBS: A component check knowledge-based system for assessing manufacturability of sheet metal parts, Journal of Materials Processing Technology, vol.172, issue.1, pp.64-69, 2006.
DOI : 10.1016/j.jmatprotec.2005.09.001

T. Kuo, S. H. Huang, and H. Zhang, Design for manufacture and design for ???X???: concepts, applications, and perspectives, Computers & Industrial Engineering, vol.41, issue.3, pp.241-260, 2001.
DOI : 10.1016/S0360-8352(01)00045-6

L. Becerra, R. Et-coello, and C. , Cultured Differential Evolution for Constrained Optimization, Computer Methods in Applied Mechanics and Engineering, vol.195, pp.33-36, 2007.

H. C. Lau, C. W. Wong, I. K. Hui, and K. F. Et-pun, Design and implementation of an integrated knowledge system, Knowledge-Based Systems, vol.16, issue.2, pp.69-76, 2003.
DOI : 10.1016/S0950-7051(02)00052-7

K. C. Laudon, Essentials of Management Information Systems, 2002.

N. Lebaal, Optimisation de la tête d'extrusion pour la fabrication de pièces thermoplastiques, Matériaux et Procédés. Nancy, Institut National Polytechnique de Lorraine Thèse de Doctorat, 2007.

N. Lebaal, F. Schmidt, S. Puissant, and D. Et-schläfli, Design of optimal extrusion die for a range of different materials, Polymer Engineering & Science, vol.27, issue.3, pp.432-440, 2009.
DOI : 10.1002/pen.21298

S. Lee, Y. Ma, G. Thimm, and J. Et-verstraeten, Product lifecycle management in aviation maintenance, repair and overhaul, Computers in Industry, vol.59, issue.2-3, pp.296-303, 2008.
DOI : 10.1016/j.compind.2007.06.022

J. Legardeur, J. F. Boujut, and H. Et-tiger, ID2: A New Tool to Foster Innovation During the Early Phases of Design Projects, Concurrent Engineering, vol.11, issue.3, pp.235-244, 2003.
DOI : 10.1177/106329303038575

F. Lehner, R. Maier, and O. Et-klosa, Organisational Memory Systems: Application of Advanced Database & Network Technologies in Organisations, 2nd International conference on Practical Aspects of Knowledge Management (PAKM'98), 1998.

E. Levner, V. Kats, A. López-de-pablo, D. Et-cheng, and T. C. , Complexity of cyclic scheduling problems: A state-of-the-art survey, Computers & Industrial Engineering, vol.59, issue.2, pp.352-361, 2010.
DOI : 10.1016/j.cie.2010.03.013

W. D. Li, W. F. Lu, J. Y. Fuh, and Y. S. Et-wong, Collaborative computer-aided design???research and development status, Computer-Aided Design, vol.37, issue.9, pp.931-940, 2005.
DOI : 10.1016/j.cad.2004.09.020

W. D. Li and Z. M. Et-qiu, State-of-the-art technologies and methodologies for collaborative product development systems, International Journal of Production Research, vol.36, issue.13, pp.2525-2559, 2006.
DOI : 10.1016/S0166-3615(02)00120-3

J. T. Lim, H. M. Rho, and K. K. Et-cho, A knowledge-based process planning system for injection mold, Computers & Industrial Engineering, vol.27, issue.1-4, pp.1-4, 1994.
DOI : 10.1016/0360-8352(94)90245-3

M. C. Lin, A Matrix Approach to the Customer-oriented Product Design, Concurrent Engineering, vol.13, issue.2, pp.95-109, 2005.
DOI : 10.1177/1063293X05053795
URL : https://hal.archives-ouvertes.fr/hal-00571178

D. T. Liu and X. W. Et-xu, A review of web-based product data management systems, Comput. Ind, vol.44, issue.3, pp.251-262, 2001.

Z. Lou, Development of an integrated knowledge-based system for mold-base design, Journal of Materials Processing Technology, vol.150, issue.1-2, pp.194-199, 2004.
DOI : 10.1016/j.jmatprotec.2004.01.037

A. M. Lovatt and H. R. Et-shercliff, Manufacturing process selection in engineering design. Part 2: a methodology for creating task-based process selection procedures, Materials & Design, vol.19, issue.5-6, pp.5-6, 1998.
DOI : 10.1016/S0261-3069(98)00039-9

S. C. Lu, W. Elmaraghy, G. Schuh, and R. Wilhelm, A SCIENTIFIC FOUNDATION OF COLLABORATIVE ENGINEERING, CIRP Annals - Manufacturing Technology, vol.56, issue.2, pp.605-634, 2007.
DOI : 10.1016/j.cirp.2007.10.010

P. G. Maropoulos, R. P. Baker, and K. Y. Et-paramor, Editorial, Journal of Materials Processing Technology, vol.107, issue.1-3, pp.1-3, 2000.
DOI : 10.1016/S0924-0136(00)00676-2

H. B. Marri, A. Gunasekaran, and R. J. Et-grieve, Computer-aided process planning: A state of art, The International Journal of Advanced Manufacturing Technology, vol.9, issue.5, pp.261-268, 1998.
DOI : 10.1007/BF01199881

G. Molcho, Y. Zipori, R. Schneor, O. Rosen, D. Goldstein et al., Computer aided manufacturability analysis: Closing the knowledge gap between the designer and the manufacturer, CIRP Annals - Manufacturing Technology, vol.57, issue.1, pp.153-158, 2008.
DOI : 10.1016/j.cirp.2008.03.046

D. Monticolo, V. Hilaire, S. Gomes, and A. Et-koukam, A multi-agent system for building project memories to facilitate the design process, Integr. Comput.-Aided Eng, vol.15, issue.1, pp.3-20, 2008.

C. T. Mosier, J. Yelle, and G. Et-walker, Survey of similarity coefficient based methods as applied to the group technology configuration problem, Omega, vol.25, issue.1, pp.65-79, 1997.
DOI : 10.1016/S0305-0483(96)00045-X

S. Mouton, D. Teissandier, P. Sébastian, and J. P. Et-nadeau, Manufacturing requirements in design: The RTM process in aeronautics, Composites Part A: Applied Science and Manufacturing, vol.41, issue.1, pp.125-130, 2010.
DOI : 10.1016/j.compositesa.2009.09.027
URL : https://hal.archives-ouvertes.fr/hal-00971367

A. Mukherjee and C. R. Liu, Conceptual design, manufacturability evaluation and preliminary process planning using function-form relationships in stamped metal parts, Robotics and Computer-Integrated Manufacturing, vol.13, issue.3, pp.253-270, 1997.
DOI : 10.1016/S0736-5845(97)00007-0

E. Mulet and R. Vidal, Functional requirements for computer-based design support systems, derived from experimental studies, Knowledge-Based Systems, vol.19, issue.1, pp.32-42, 2006.
DOI : 10.1016/j.knosys.2005.08.003

B. Mutel and A. Et-clément, Computer-Aided Group Technology Integrated System, CIRP Annals - Manufacturing Technology, vol.37, issue.1, pp.425-428, 1988.
DOI : 10.1016/S0007-8506(07)61669-2

Y. Nahm and H. Et-ishikawa, Integrated Product and Process Modeling for Collaborative Design Environment, Concurrent Engineering, vol.12, issue.1, pp.5-23, 2004.
DOI : 10.1177/1063293X04040440

S. Y. Nof, V. N. Rajan, and E. Et-lenz, Automatic Generation of Assembly Constraints and Cooperation Task Planning, CIRP Annals - Manufacturing Technology, vol.42, issue.1, pp.13-16, 1993.
DOI : 10.1016/S0007-8506(07)62381-6

J. B. Noh, K. C. Lee, J. K. Kim, J. K. Lee, and S. H. Kim, A case-based reasoning approach to cognitive map-driven tacitknowledge management, Expert Systems with Applications, vol.19, issue.4, pp.249-259, 2000.
DOI : 10.1016/S0957-4174(00)00037-3

I. Nonaka and H. Takeuchi, The knowledge-creating company: How Japanese companies create the dynamics of innovation, Long Range Planning, vol.29, issue.4, 1995.
DOI : 10.1016/0024-6301(96)81509-3

J. Noor, A comprehensive approach to complex system product development : Operations management tools applied to automotive design, 2007.

P. Nowak, R. Postansque, P. Lafon, and B. Et-eynard, Implémentation de KBE, pp.107-121, 2004.

S. Ohsuga, Toward intelligent CAD systems, Computer-Aided Design, vol.21, issue.5, pp.315-337, 1989.
DOI : 10.1016/0010-4485(89)90039-0

L. Olsen, F. F. Samavati, M. C. Sousa, and J. A. Et-jorge, Sketch-based modeling: A survey, Computers & Graphics, vol.33, issue.1, pp.85-103, 2009.
DOI : 10.1016/j.cag.2008.09.013

S. K. Ong, M. J. Sun, and A. Y. Et-nee, A fuzzy set AHP-based DFM tool for rotational parts, Journal of Materials Processing Technology, vol.138, issue.1-3, pp.1-3, 2003.
DOI : 10.1016/S0924-0136(03)00076-1

N. Ozturk, Neuro-Genetic Design Optimization Framework to Support the Integrated Robust Design Optimization Process in CE, Concurrent Engineering, vol.14, issue.1, pp.5-16, 2006.
DOI : 10.1177/1063293X06063314

G. Pahl and W. Et-beitz, Engineering design -A systematic approach, 1996.

J. Pankakoski, E. Eloranta, M. Luhtala, and J. Et-nikkola, Applying case-based reasoning to manufacturing systems design, Computer Integrated Manufacturing Systems, vol.4, issue.4, pp.212-220, 1991.
DOI : 10.1016/0951-5240(91)90013-O

H. Peck, Designing For Manufacture (Topics In Engineering Design), 1973.

J. A. Penoyer, G. Burnett, D. J. Fawcett, and S. Y. Et-liou, Knowledge based product life cycle systems: principles of integration of KBE and C3P, Computer-Aided Design, vol.32, issue.5-6, pp.311-320, 2000.
DOI : 10.1016/S0010-4485(00)00014-2

M. Pinfold and C. Et-chapman, The application of KBE techniques to the FE model creation of an automotive body structure, Computers in Industry, vol.44, issue.1, pp.1-10, 2001.
DOI : 10.1016/S0166-3615(00)00079-8

R. Plant and R. Et-gamble, Methodologies for the development of knowledge-based systems, 1982???2002, The Knowledge Engineering Review, vol.18, issue.1, pp.47-81, 2003.
DOI : 10.1017/S026988890300064X

B. Prasad, R. S. Morenc, and R. M. Et-rangan, Information Management for Concurrent Engineering: Research Issues, Concurrent Engineering, vol.1, issue.1, pp.3-20, 1993.
DOI : 10.1177/1063293X9300100102

Z. Qiu, K. Kok, Y. Wong, and J. Et-fuh, Role-based 3D visualisation for asynchronous PLM collaboration, Computers in Industry, vol.58, issue.8-9, pp.8-9, 2007.
DOI : 10.1016/j.compind.2007.02.006

M. Rezayat, Knowledge-based product development using XML and KCs, Computer-Aided Design, vol.32, issue.5-6, pp.299-309, 2000.
DOI : 10.1016/S0010-4485(00)00013-0

M. M. Richter, The search for knowledge, contexts, and Case-Based Reasoning, Engineering Applications of Artificial Intelligence, vol.22, issue.1, pp.3-9, 2009.
DOI : 10.1016/j.engappai.2008.04.021

A. Riou and C. Et-mascle, Assisting designer using feature modeling for lifecycle, Computer-Aided Design, vol.41, issue.12, pp.1034-1049, 2009.
DOI : 10.1016/j.cad.2009.08.004

P. Roques, SysML par l'exemple : Un langage de modélisation pour systèmes complexes, Eyrolles, pp.978-980, 2009.

L. Roucoules, B. Eynard, P. Nowak, and A. Et-skander, Une approche "au juste nécessaire" de l'intégration métier en conception vers des solutions alternatives innovantes. Ingénierie de la conception en cycle de vie des produits, pp.2-7462, 2006.

L. Roucoules and S. Et-tichkiewitch, CoDE: A Cooperative Design Environment--A New Generation of CAD Systems, Concurrent Engineering, vol.8, issue.4, pp.263-280, 2000.

R. Roy, S. Hinduja, and R. Et-teti, Recent advances in engineering design optimisation: Challenges and future trends, CIRP Annals - Manufacturing Technology, vol.57, issue.2, pp.697-715, 2008.
DOI : 10.1016/j.cirp.2008.09.007

W. W. Royce, Managing the Development of Large Software Systems, 1970.

L. Sabourin, A. Lefebvre, J. Renaud, and G. Et-gogu, Capitalisation et formalisation de savoir-faire pour la conception de??gammes d'usinage s??rieKnowledge capitalisation for process planning design as applied to??mass-produced parts, M??canique & Industries, vol.3, issue.2, pp.121-128, 2002.
DOI : 10.1016/S1296-2139(02)01148-X

J. Sánchez, J. W. Priest, and R. Soto, Intelligent reasoning assistant for incorporating manufacturability issues into the design process, Expert Systems with Applications, vol.12, issue.1, pp.81-88, 1997.
DOI : 10.1016/S0957-4174(96)00082-6

M. Sandberg, Knowledge Based Engineering -In product development, 2003.

S. M. Sapuan, M. R. Osman, and Y. Et-nukman, State of the art of the concurrent engineering technique in the automotive industry, Journal of Engineering Design, vol.3, issue.2, pp.143-157, 2006.
DOI : 10.1108/01443579410072337

C. Scaffidi, C. Bogart, M. Burnett, A. Cypher, B. Myers et al., Using traits of web macro scripts to predict reuse, Journal of Visual Languages & Computing, vol.21, issue.5, 2010.
DOI : 10.1016/j.jvlc.2010.08.003

D. Scaravetti, Formalisation préalable d'un problème de conception, pour l'aide à la décision en conception préliminaire, 2004.

R. C. Schank and R. P. Et-albeson, SCRIPTS, PLANS, GOALS, AND UNDERSTANDING, 1977.
DOI : 10.1016/B978-1-4832-1446-7.50019-4
URL : https://hal.archives-ouvertes.fr/hal-00692030

M. Schütz and H. Schwefel, Evolutionary approaches to solve three challenging engineering tasks, Computer Methods in Applied Mechanics and Engineering, vol.186, issue.2-4, pp.2-4, 2000.
DOI : 10.1016/S0045-7825(99)00382-5

K. Schützer, A. L. Helleno, and S. C. Et-pereira, The influence of the manufacturing strategy on the production of molds and dies, Journal of Materials Processing Technology, vol.179, issue.1-3, pp.1-3, 2006.
DOI : 10.1016/j.jmatprotec.2006.03.098

P. Serrafero, Vers la mesure de la quantité de connaissance et de compétence industrielle : le modèle KnoVA, 1er colloque du Groupe de Gestion des Compétences et des Connaissances en Génie Industriel, 2002.

P. Serrafero, S. Gomes, D. Bonnivard, and L. Et-jézéquel, De la mémoire projet à la compétence métier : vers la synthèse de connaissances métier en ingénierie robuste des produits/process, 6th International conference on Integrated Design and Manufacturing in Mechanical Engineering (IDMME'06), 2006.

P. Serrafero, S. Gomes, and D. Et-monticolo, Ingénierie innovante, collaborative et apprenante en développement automobile : Vers une CAO en 5D au service de la mobilité congruente, 2007.

J. J. Shah and M. Et-mantyla, Parametric and Feature Based CAD/Cam: Concepts, Techniques, and Applications, p.471002143, 1995.

S. Shanker and D. Et-jansson, A generalized methodology for evaluating manufacturability. Concurrent Engineering, Contemporary Issues and Modern Design Tools, pp.248-263, 1993.

K. Shelesh-nezhad and E. Et-siores, An intelligent system for plastic injection molding process design, Journal of Materials Processing Technology, vol.63, issue.1-3, pp.1-3, 1997.
DOI : 10.1016/S0924-0136(96)02664-7

H. R. Shercliff and A. M. Lovatt, Selection of manufacturing processes in design and the role of process modelling, Progress in Materials Science, vol.46, issue.3-4, pp.3-4, 2001.
DOI : 10.1016/S0079-6425(00)00013-X

M. Shipulski, Design for Manufacturing -What it is and how does it fit with Design for Function, Design for Assembly and Design for Cost? 2007 International Forum on DFMA, 2007.

E. Shkvar, Mathematical Modeling of Turbulent Flow Control by Using Wall Jets and Polymer Additives Poster Paper, ASME Pressure Vessels and Piping Conference, pp.277-283, 2001.

L. Shu-hsien, Expert system methodologies and applications???a decade review from 1995 to 2004, Expert Systems with Applications, vol.28, issue.1, pp.93-103, 1995.
DOI : 10.1016/j.eswa.2004.08.003

B. Sid, M. Domaszewski, and F. Et-peyraut, Topology optimization using an adaptive genetic algorithm and a new geometric representation, Computer Aided Optimum Design in Engineering IX, pp.480-978, 2005.

J. Silva and K. H. Chang, Design Parameterization for Concurrent Design and Manufacturing of Mechanical Systems, Concurrent Engineering, vol.10, issue.1, pp.3-14, 2002.
DOI : 10.1177/1063293X02010001048

A. Skander, Méthode et modèle DFM pour le choix des procédés et l'intégration des contraintes de fabrication vers l'émergence de la solution produit, LAboratoire des Systèmes Mécaniques et d'Ingénierie Simultanée (LASMIS). Troyes Thèse de Doctorat, 2006.

W. Skarka, Application of MOKA methodology in generative model creation using CATIA, Engineering Applications of Artificial Intelligence, vol.20, issue.5, pp.677-690, 2007.
DOI : 10.1016/j.engappai.2006.11.019

G. Sohlenius, Concurrent Engineering. Annals of the CIRP, pp.645-655, 1992.

F. Sourd and J. Et-rogerie, Continuous filling and emptying of storage systems in constraint-based scheduling, European Journal of Operational Research, vol.165, issue.2, pp.510-524, 2005.
DOI : 10.1016/j.ejor.2004.04.019
URL : https://hal.archives-ouvertes.fr/hal-01185227

J. Stark, Product Lifecycle Management : 21st Century Paradigm for Product Realisation, pp.978-1852338107, 2004.

L. Steels, Corporate Knowledge Management. ISMICK'93, Barthès Proc, 1993.

C. J. Su, M. M. Tseng, and R. J. Mayer, EKAMD--A Knowledge-Based Concurrent Engineering Support System, Concurrent Engineering, vol.5, issue.1, pp.59-76, 1997.
DOI : 10.1177/1063293X9700500107

J. C. Sugiono, Application development in a knowledge-based conceptual generator. Department of Civil and Environmental Engineering, 1992.

N. P. Suh, Application of Axiomatic Design. Integration of Process Knowledge into Design Support, 1999.

G. Sun, C. H. Sequin, and P. K. Wright, Operation decomposition for freeform surface features in process planning, Computer-Aided Design, vol.33, issue.9, pp.621-636, 2001.
DOI : 10.1016/S0010-4485(01)00068-9

K. G. Swift, Process Selection: From Design to Manufacture, 2003.

K. G. Swift and N. J. Et-brown, DFM Experiences and Strategies for Implementation. 2001 International Forum on DFMA "Concepts For The New Millennium, 2001.

M. Takahashi, J. Oono, K. Saitoh, and S. Et-matsumoto, Reusing makes it easier: manufacturing process design by CBR with KnowledgeWare, IEEE Expert, vol.10, issue.6, pp.74-80, 1995.
DOI : 10.1109/64.483255

D. Tang and X. Et-qian, Product lifecycle management for automotive development focusing on supplier integration, Computers in Industry, vol.59, issue.2-3, pp.288-295, 2008.
DOI : 10.1016/j.compind.2007.07.002

R. Teti and S. R. Et-kumara, Intelligent Computing Methods for Manufacturing Systems, CIRP Annals - Manufacturing Technology, vol.46, issue.2, pp.629-652, 1997.
DOI : 10.1016/S0007-8506(07)60883-X

S. Tichkiewitch, De la CFAO à la conception intégrée, pp.298-0924, 1994.

S. L. Ting, W. M. Wang, S. K. Kwok, A. H. Tsang, and W. B. Et-lee, RACER: Rule-Associated CasE-based Reasoning for supporting General Practitioners in prescription making, Expert Systems with Applications, vol.37, issue.12
DOI : 10.1016/j.eswa.2010.05.080

A. Tiwari, Evolutionary Computing Techniques for Handling Variable Interaction in Engineering Design Optimisation. Cranfield, 2001.

T. Tomiyama, V. D-'amelio, J. Urbanic, and W. Et-elmaraghy, Complexity of Multi-Disciplinary Design, CIRP Annals - Manufacturing Technology, vol.56, issue.1, pp.185-188, 2007.
DOI : 10.1016/j.cirp.2007.05.044

T. Tomiyama, P. Gu, Y. Jin, D. Lutters, C. Kind et al., Design methodologies: Industrial and educational applications, CIRP Annals - Manufacturing Technology, vol.58, issue.2, pp.543-565, 2009.
DOI : 10.1016/j.cirp.2009.09.003
URL : http://doc.utwente.nl/73037/1/Tomiyama09design.pdf

E. Turban and J. E. Et-aronson, Decision Support Systems and Intelligent Systems, 2000.

G. Van-heijst, R. Van-der-spek, and E. Et-kruizinga, Organizing Corporate Memories, 10th Banff Knowledge Acquisition for Knowledge-Based Systems Workshop (KAW'96), 1996.

A. R. Venkatachalam, Automating manufacturability evaluation in CAD systems through expert systems approaches, Expert Systems with Applications, vol.7, issue.4, pp.495-506, 1994.
DOI : 10.1016/0957-4174(94)90074-4

V. J. Vliet, C. Luffervelt, and H. Et-kals, State of the art report on design for manufacturing. ASME design engineering technical conference DETC99/DFM-8970, 1999.

G. Von-krogh, I. Nonaka, and M. Et-aben, Making the Most of Your Company's Knowledge: A Strategic Framework, Long Range Planning, vol.34, issue.4, pp.421-439, 2001.
DOI : 10.1016/S0024-6301(01)00059-0

K. Waiyagan and E. L. Et-bohez, Intelligent feature based process planning for five-axis mill-turn parts, Computers in Industry, vol.60, issue.5, pp.296-316, 2009.
DOI : 10.1016/j.compind.2008.09.009

D. L. Waltz, Generating Semantic Descriptions from Drawings of Scenes With Shadows, 1972.

J. Wang, C. A. Roberts, and S. Et-danielson, Local and Global Accessibility Evaluation with Tool Geometry, Computer-Aided Design and Applications, vol.116, issue.1-4, pp.1-4, 2007.
DOI : 10.1080/16864360.2007.10738522

I. Watson, Understanding case-based reasoning. Applying Knowledge Management, pp.23-46, 2003.
DOI : 10.1016/b978-155860760-6/50002-9

J. L. Whitten, L. D. Bentley, and K. C. Et-dittman, Systems Analysis and Design Methods, 2004.

S. S. Willaert, R. De-graaf, and S. Et-minderhoud, Collaborative engineering: A case study of Concurrent Engineering in a wider context, Journal of Engineering and Technology Management, vol.15, issue.1, pp.87-109, 1998.
DOI : 10.1016/S0923-4748(97)00026-X

B. Willard, UML for systems engineering, Computer Standards & Interfaces, vol.29, issue.1, pp.69-81, 2007.
DOI : 10.1016/j.csi.2005.12.006

C. B. Williams, J. K. Allen, D. W. Rosen, and F. Et-mistree, Designing Platforms for Customizable Products and Processes in Markets of Non-Uniform Demand, Concurrent Engineering, vol.15, issue.2, pp.201-216, 2007.
DOI : 10.1177/1063293X07079328

N. Wognum and A. Et-trappey, PLM challenges, Advanced Engineering Informatics, vol.22, issue.4, pp.419-420, 2008.
DOI : 10.1016/j.aei.2008.07.007

J. Q. Yan, X. G. Ming, W. F. Lu, and X. F. Et-zha, Special issue on : New Research Advances in Product Lifecycle Management, Concurrent Engineering, vol.16, issue.4, p.241, 2008.

B. Yang, T. Han, and Y. Kim, Integration of ART-Kohonen neural network and case-based reasoning for intelligent fault diagnosis, Expert Systems with Applications, vol.26, issue.3, pp.387-395, 2004.
DOI : 10.1016/j.eswa.2003.09.009

B. Yannou, Les apports de la programmation par contraintes en conception. Conception de produits mécaniques: méthodes, modèles et outils. M. Tollenaere, pp.2-86601, 1998.

E. Yechiam, Why are macros not used? A brief review and an approach for improving training, Computers & Education, vol.46, issue.2, pp.206-220, 2006.
DOI : 10.1016/j.compedu.2004.08.009

R. T. Yeh, Notes on concurrent engineering, IEEE Transactions on Knowledge and Data Engineering, vol.4, issue.5, pp.407-414, 1992.
DOI : 10.1109/69.166983

Y. Lee, J. Kim, and K. , A feature-based approach to extracting machining features, Computer-Aided Design, vol.30, issue.13, pp.1019-1035, 1998.
DOI : 10.1016/S0010-4485(98)00055-4

M. Yoshimura, System Design Optimization for Product Manufacturing, Concurrent Engineering, vol.15, issue.4, pp.329-343, 2007.
DOI : 10.1177/1063293X07083087

J. Yu, S. Krizan, and K. Et-ishii, Computer-aided design for manufacturing process selection, Journal of Intelligent Manufacturing, vol.9, issue.11, pp.199-208, 1993.
DOI : 10.1007/BF00123964

P. A. Yvars, Contribution à la représentation des connaissances en ingénierie intégrée de produits et de systèmes automatisés de production, 2001.

P. A. Yvars and A. Saucier, Modélisation objet de produits pour l'ingénierie d'ensembles mécaniques. 01 Design'97 Les objets en, 1997.

M. Zaclad and M. Et-grundstein, Ingénierie et capitalisation des connaissances, 2001.

M. Zaeh, T. Oertli, and J. Et-milberg, Finite Element Modelling of Ball Screw Feed Drive Systems, CIRP Annals - Manufacturing Technology, vol.53, issue.1, pp.289-292, 2004.
DOI : 10.1016/S0007-8506(07)60700-8

H. C. Zhang and Z. Et-daguang, Concurrent Engineering: An Overview from Manufacturing Engineering Perspectives, Concurrent Engineering, vol.3, issue.3, pp.221-236, 1995.
DOI : 10.1177/1063293X9500300308

Z. Zhao and J. J. Et-shah, Domain independent shell for DfM and its application to sheet metal forming and injection molding, Computer-Aided Design, vol.37, issue.9, pp.881-898, 2005.
DOI : 10.1016/j.cad.2004.09.016

L. Y. Zheng, C. A. Mcmahon, L. Li, L. Ding, and J. Et-jamshidi, Key characteristics management in product lifecycle management: a survey of methodologies and practices, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, vol.222, issue.8, pp.989-1008, 2008.
DOI : 10.1243/09544054JEM1045

M. C. Ziemke and M. S. Et-spann, Concurrent engineering's roots in the world war II era. Concurrent Engineering, contemporary Issues and Modern Design tools, pp.24-41, 1993.