R. F. Bunshah, Handbook of hard coatings. Deposition technologies, properties and applications, 2001.

P. Fauchais, M. Fukumoto, A. Vardelle, and M. Vardelle, Knowledge Concerning Splat Formation: An Invited Review, Journal of Thermal Spray Technology, vol.13, issue.3, pp.337-360, 2004.
DOI : 10.1361/10599630419670

H. Herman, S. Sampath, and R. C. Mccune, Thermal Spray: Current Status and Future Trends, MRS Bulletin, vol.15, issue.07, pp.17-25, 2000.
DOI : 10.1557/mrs2000.119

M. Dorfman, Thermal spray basics, Adv. Mater. Process, issue.7, pp.47-50, 2002.

M. Fukumoto, M. Shiiba, H. Kaji, and T. Yasui, Three-dimensional transition map of flattening behavior in the thermal spray process, Pure and Applied Chemistry, vol.77, issue.2, pp.77-429, 2005.
DOI : 10.1351/pac200577020429

F. Otsubo, H. Era, and K. Kishitake, Interface Reaction between Nickel-Base Self-Fluxing Alloy Coating and Steel Substrate, Journal of Thermal Spray Technology, vol.9, issue.2, pp.259-263, 2000.
DOI : 10.1361/105996300770350014

H. Du, J. H. Shin, and S. W. Lee, Study on Porosity of Plasma-Sprayed Coatings by Digital Image Analysis Method, Journal of Thermal Spray Technology, vol.14, issue.4, pp.453-461, 2005.
DOI : 10.1361/105996305X76450

J. M. Guilemany, J. Nutting, and M. J. Dougan, A transmission electron microscopy study of the microstructures present in alumina coatings produced by plasma spraying, Journal of Thermal Spray Technology, vol.1, issue.No. 1
DOI : 10.1007/s11666-997-0025-5

S. Chandra and P. Fauchais, Formation of Solid Splats During Thermal Spray Deposition, Journal of Thermal Spray Technology, vol.201, issue.507, pp.148-180, 2009.
DOI : 10.1007/s11666-009-9294-5
URL : https://hal.archives-ouvertes.fr/hal-00393097

J. Cedelle, M. Vardelle, and P. Fauchais, Influence of stainless steel substrate preheating on surface topography and on millimeter- and micrometer-sized splat formation, Surface and Coatings Technology, vol.201, issue.3-4
DOI : 10.1016/j.surfcoat.2006.02.003
URL : https://hal.archives-ouvertes.fr/hal-00131174

J. Cedelle, M. Vardelle, B. Pateyron, and P. Fauchais, Investigation of plasma sprayed coatings formation by visualization of droplet impact and splashing on a smooth substrate, IEEE Transactions on Plasma Science, vol.33, issue.2, pp.414-415, 2005.
DOI : 10.1109/TPS.2005.845121

R. Dhiman, A. G. Mcdonald, and S. Chandra, Predicting splat morphology in a thermal spray process, Surface and Coatings Technology, vol.201, issue.18, pp.7789-7801, 0201.
DOI : 10.1016/j.surfcoat.2007.03.010

R. Ghafouri-azar, S. Shakeri, S. Chandra, and J. Mostaghimi, Interactions between molten metal droplets impinging on a solid surface, International Journal of Heat and Mass Transfer, vol.46, issue.8, pp.46-1395, 2003.
DOI : 10.1016/S0017-9310(02)00403-9

S. Goutier, M. Vardelle, J. C. Labbe, and P. Fauchais, Alumina Splat Investigation: Visualization of Impact and Splat/Substrate Interface for Millimeter-Sized Drops, Journal of Thermal Spray Technology, vol.385, issue.121
DOI : 10.1007/s11666-009-9432-0

L. Bianchi, A. Denoirjean, F. Blein, and P. Fauchais, Microsctructural investigation of plasma-sprayed ceramic splats, Thin Solid Films, pp.299-125, 1997.

J. Mostaghimi and S. Chandra, Splat formation in plasma-spray coating process, Pure and Applied Chemistry, vol.74, issue.3, pp.441-445, 2002.
DOI : 10.1351/pac200274030441

M. Pasandideh-fard, S. Chandra, and J. Mostaghimi, A three-dimensional model of droplet impact and solidification, International Journal of Heat and Mass Transfer, vol.45, issue.11, pp.45-2229, 2002.
DOI : 10.1016/S0017-9310(01)00336-2

S. Sampath and X. Jiang, Splat formation and microstructure development during plasma spraying: deposition temperature effects, Materials Science and Engineering: A, vol.304, issue.306, pp.304-306, 2001.
DOI : 10.1016/S0921-5093(00)01464-7

H. Zhang, X. Y. Wang, L. L. Zheng, and X. Y. Jiang, Studies of splat morphology and rapid solidification during thermal spraying, International Journal of Heat and Mass Transfer, vol.44, issue.24, pp.44-4579, 2001.
DOI : 10.1016/S0017-9310(01)00109-0

H. Li, S. Costil, H. Liao, C. Li, M. Planche et al., Effects of surface conditions on the flattening behavior of plasma sprayed Cu splats, Surface and Coatings Technology, vol.200, issue.18-19, pp.5435-5446, 0200.
DOI : 10.1016/j.surfcoat.2005.07.058

L. Bianchi, A. C. Leger, M. Vardelle, A. Vardelle, and P. Fauchais, Splat formation and cooling of plasma-sprayed zirconia, Thin Solid Films, vol.305, issue.1-2, pp.305-340, 1997.
DOI : 10.1016/S0040-6090(97)80005-3

T. Chraska and A. H. King, Effect of different substrate conditions upon interface with plasma sprayed zirconie -a TEM study, Surf. Coat. Technol, pp.157-238, 2002.

Z. G. Feng, M. Domaszewski, G. Montavon, and C. Coddet, Finite Element Analysis of Effect of Substrate Surface Roughness on Liquid Droplet Impact and Flattening Process, Journal of Thermal Spray Technology, vol.11, issue.1
DOI : 10.1361/105996302770348989

. Labbe, Influence of surbstrate surface conditions on the plasma sprayed ceramic and metallic particles flattening, Surf. Coat. Technol, pp.2317-2331, 0200.

C. Li and J. Li, Evaporated-gas-induced splashing model for splat formation during plasma spraying, Surface and Coatings Technology, vol.184, issue.1, pp.184-197, 2004.
DOI : 10.1016/j.surfcoat.2003.10.048

M. Fukumoto, E. Nishioka, and T. Matsubara, Flattening solidification behavior of a metal droplet on a flat substrate surface held at various temperatures, Surf

A. Mcdonald, C. Moreau, and S. Chandra, Thermal contact resistance between plasmasprayed particles and flat surfaces, Int. J. Heat Mass Transf, pp.50-1737, 2007.

M. Fukumoto, H. Nagai, and T. Yasui, Influence of Surface Character Change of Substrate Due to Heating on Flattening Behavior of Thermal Sprayed Particles, Journal of Thermal Spray Technology, vol.15, issue.4, pp.759-764, 2006.
DOI : 10.1361/105996306X146776

S. Sampath, X. Y. Jiang, J. Matejicek, A. C. Leger, and A. Vardelle, Substrate temperature effects on splat formation, microstructure development and properties of plasma sprayed coatings Part I: Case study for partially stabilized zirconia, Materials Science and Engineering: A, vol.272, issue.1
DOI : 10.1016/S0921-5093(99)00459-1

Y. Tanaka and M. Fukumoto, Investigation of dominating factors on flattening behavior of plasma sprayed ceramic particles, Surface and Coatings Technology, vol.120, issue.121, pp.120-121, 1999.
DOI : 10.1016/S0257-8972(99)00348-5

X. Y. Jiang, Y. Wan, H. Herman, and S. Sampath, Role of condensates and adsorbates on substrate surface on fragmentation of impinging molten droplets during thermal spray, Thin Solid Films, vol.385, issue.1-2, pp.385-132, 2001.
DOI : 10.1016/S0040-6090(01)00769-6

M. Fukumoto and Y. Huang, Flattening Mechanism in Thermal Sprayed Nickel Particle Impinging on Flat Substrate Surface, Journal of Thermal Spray Technology, vol.8, issue.3, pp.427-432, 1999.
DOI : 10.1361/105996399770350386

M. Pasandideh-fard, V. Pershin, S. Chandra, and J. Mostaghimi, Splat Shapes in a Thermal Spray Coating Process: Simulations and Experiments, Journal of Thermal Spray Technology, vol.11, issue.2, pp.206-217, 2002.
DOI : 10.1361/105996302770348862

S. Kitahara and A. Hasui, A study of the bonding mechanism of sprayed coatings, Journal of Vacuum Science and Technology, vol.11, issue.4
DOI : 10.1116/1.1312746

L. Li, X. Y. Wang, G. Wei, A. Vaidya, H. Zhang et al., Substrate melting during thermal spray splat quenching, Thin Solid Films, vol.468, issue.1-2, pp.468-113, 2004.
DOI : 10.1016/j.tsf.2004.05.073

J. A. Browning, Hypervelocity impact fusion???a technical note, Journal of Thermal Spray Technology, vol.1, issue.4, pp.289-292, 1992.
DOI : 10.1007/BF02647155

H. Sampath and . Herman, On the role of the particle state and deposition procedure on mechanical, tribological and dielectric response of high velocity oxy-fual sprayed alumina coatings, Mater. Sci. Eng, pp.415-416, 2006.

W. J. Trompetter, M. Hyland, D. Mcgrouther, P. Munroe, and A. Markwitz, Effect of Substrate Hardness on Splat Morphology in High-Velocity Thermal Spray Coatings, Journal of Thermal Spray Technology, vol.15, issue.4
DOI : 10.1361/105996306X147261

P. Bansal, P. H. Shipway, and S. B. Leen, Effect of Particle Impact on Residual Stress Development in HVOF Sprayed Coatings, Journal of Thermal Spray Technology, vol.15, issue.4, pp.570-575, 2006.
DOI : 10.1361/105996306X146703

C. J. Kong, P. D. Brown, S. J. Harris, and D. G. Mccartney, The microsctructure of a thermally sprayed and heat treated Al-20 wt.%Sn-3 wt.Si% alloy, Mater. Sci. Eng, pp.403-205, 2005.

T. Marrocco, L. C. Driver, S. J. Harris, and D. G. Mccartney, Microstructure and Properties of Thermally Sprayed Al-Sn-Based Alloys for Plain Bearing Applications, Journal of Thermal Spray Technology, vol.15, issue.4
DOI : 10.1361/105996306X147009

J. M. Guilemany, J. Nutting, J. R. Miguel, and Z. Dong, Microstructure characterization of WC-Ni coatings obtained by HVOF thermal spraying, Scripta Metallurgica et Materialia, vol.33, issue.1, pp.55-61, 1995.
DOI : 10.1016/0956-716X(95)00045-W

S. V. Klinkov, V. F. Kosarev, and M. Rein, Cold spray deposition: Significance of particle impact phenomena, Aerospace Science and Technology, vol.9, issue.7, pp.582-591, 2005.
DOI : 10.1016/j.ast.2005.03.005

R. C. Dykhuizen, M. F. Smith, D. L. Gilmore, R. A. Neiser, X. Jiang et al., Impact of High Velocity Cold Spray Particles, Journal of Thermal Spray Technology, vol.8, issue.4, pp.559-564, 1999.
DOI : 10.1361/105996399770350250

L. Ajdelsztajn, A. Zúñiga, B. Jodoin, and E. J. Lavernia, Cold gas dynamic spraying of a high temperature Al alloy, Surface and Coatings Technology, vol.201, issue.6, pp.2109-2116, 0201.
DOI : 10.1016/j.surfcoat.2005.06.001

B. S. Sidhu and S. Prakash, Nickel-Chromium Plasma Spray Coatings: A Way to Enhance Degradation Resistance of Boiler Tube Steels in Boiler Environment, Journal of Thermal Spray Technology, vol.15, issue.1, pp.131-140, 2006.
DOI : 10.1361/105996306X92695

V. Higuera, J. Belzunce, A. Carriles, and S. Poveda, Influence of the thermal-spray procedure on the properties of a nickel-chromium coating, Journal of materials science, pp.37-649, 2002.

A. T. Tran, M. M. Hyland, Q. T. , W. B. , and B. J. James, Effects of Surface Chemistry on Splat Formation During Plasma Spraying, Journal of Thermal Spray Technology, vol.48, issue.25-26, pp.5-6, 2008.
DOI : 10.1007/s11666-008-9237-6

S. Brossard, P. R. Munroe, A. T. Tran, and M. M. Hyland, Study of the microstructure of NiCr splats plasma sprayed on to stainless steel substrates by TEM, Surface and Coatings Technology, vol.204, issue.9-10, pp.9-10, 2010.
DOI : 10.1016/j.surfcoat.2009.10.007

P. R. Munroe, The application of focused ion beam microscopy in the material sciences, Materials Characterization, vol.60, issue.1, pp.60-62, 2009.
DOI : 10.1016/j.matchar.2008.11.014

C. Escure, M. Vardelle, and P. Fauchais, Experimental and theoretical strudy of the impact of alumina droplets on cold and hot substrates, Plasma Chemistry and Plasma Processing, vol.23, issue.2, pp.185-221, 2003.
DOI : 10.1023/A:1022976914185

A. T. Tran, S. Brossard, M. M. Hyland, and P. R. Munroe, Evidence of Substrate Melting of NiCr Particles on Stainless Steel Substrate by Experimental Observation and Simulations, Plasma Chemistry and Plasma Processing, vol.234, issue.236, pp.29-475, 2009.
DOI : 10.1007/s11090-009-9192-0

M. Xue, S. Chandra, and J. Mostaghimi, Investigation of Splat Curling up in Thermal Spray Coatings, Journal of Thermal Spray Technology, vol.15, issue.4, pp.531-536, 2006.
DOI : 10.1361/105996306X147315

A. T. Tran and M. M. Hyland, The Role of Substrate Surface Chemistry on Splat Formation During Plasma Spray Deposition by Experiments and Simulations, Journal of Thermal Spray Technology, vol.50, issue.25-26
DOI : 10.1007/s11666-009-9414-2

J. Stringer, B. A. Wilcox, and R. I. Jaffee, The high-temperature oxidation of nickel - 20wt% chromium alloys containing dispersed oxide phases, Oxidation of metals, 1972.

S. Inada and W. Yang, Solidification of molten metal droplets impinging on a cold surface, Exp Heat Transf, pp.93-100, 1994.

M. Vardelle, A. Vardelle, A. C. Leger, P. Fauchais, and D. Gobin, Influence of particle parameters at impact on splat formation and solidification in plasma spraying processes, Journal of Thermal Spray Technology, vol.1, issue.1
DOI : 10.1007/BF02648528

A. P. Grosvenor, B. A. Kobe, and N. S. Mcintyre, Examination of the oxidation of iron by oxygen using X-ray photoelectron spectroscopy and QUASES, Surf. Sci, pp.565-151, 2004.

A. P. Grosvenor, B. A. Kobe, and N. S. Mcintyre, Studies of the oxidation of iron by water vapour using X-ray photoelectron spectroscopy and QUASES???, Surface Science, vol.572, issue.2-3, pp.572-217, 2004.
DOI : 10.1016/j.susc.2004.08.035

S. B. Newcomb, A microsctructural study of the oxidation of Ni-Cr steels in air and in CO-CO2, 1982.

G. C. Allen, J. M. Dyke, S. J. Harris, and A. Morries, A surface study of the oxidation of type 304L stainless steel at 600K in air, Oxid. Met, issue.56, pp.29-391, 1988.

J. Dünnwald and A. Otto, An investigation of phase transitions in rust layers using raman spectroscopy, Corrosion Science, vol.29, issue.9, pp.1167-1176, 1989.
DOI : 10.1016/0010-938X(89)90052-8

. Strutt, The dependency of microstructure and properties of nanostructured coatings on plasma spray conditions, Surf. Coat. Technol, vol.130, pp.1-8, 2000.

K. A. Khor, Z. L. Dong, C. H. Quek, and P. Cheang, Microstructure investigation of plasma sprayed HA/Ti6Al4V composites by TEM, Materials Science and Engineering: A, vol.281, issue.1-2, pp.281-221, 2000.
DOI : 10.1016/S0921-5093(99)00717-0

S. Sampath and H. Herman, Rapid solidification and microstructure development during plasma spray deposition, Journal of Thermal Spray Technology, vol.45, issue.9, pp.445-456, 1996.
DOI : 10.1007/BF02645275

S. Brossard, P. R. Munroe, A. T. Tran, and M. M. Hyland, Study of the effects of surface chemistry on splat formation for plasma sprayed NiCr onto stainless steel substrates, Surface and Coatings Technology, vol.204, issue.9-10, pp.9-10, 2010.
DOI : 10.1016/j.surfcoat.2009.10.008

D. B. Williams and C. B. Carter, Transmission electron microscopy: a textbook for materials science, 1996.
DOI : 10.1007/978-1-4757-2519-3

P. Nash, The Cr-Ni (Chromium-Nickel) system, Bull. Alloy Ph, Diagr, vol.7, issue.5, pp.466-476, 1986.

N. S. Mcintyre, T. C. Chan, and C. Chen, Characterization of oxide structures formed on nickel-chromium alloy during low pressure oxidation at 500-600°C, Oxidation of metals, pp.33-457, 1990.

A. A. Syed, A. Denoirjean, P. Denoirjean, J. C. Labbe, and P. , In-Flight Oxidation of Stainless Steel Particles in Plasma Spraying, Journal of Thermal Spray Technology, vol.14, issue.1, pp.117-124, 2005.
DOI : 10.1361/10599630522675

R. Mcpherson, Formation of metastable phases in flame- and plasma-prepared alumina, Journal of Materials Science, vol.48, issue.6, pp.851-858, 1973.
DOI : 10.1007/BF02397914

V. V. Sobolev, J. M. Guilemany, and A. J. Martin, Influence of surface roughness on the flattening of powder particles during thermal spraying, Journal of Thermal Spray Technology, vol.54, issue.5, pp.207-214, 1996.
DOI : 10.1007/BF02646434

R. H. Jones, Environmental effects on engineered materials, 2001.
DOI : 10.1201/9780203908129

R. S. Alwitt, Aluminium-water system, Oxid. Oxid Films, pp.169-254, 1976.

W. J. Trompetter, M. M. Hyland, D. Mcgrouther, P. R. Munroe, and A. Markwitz, The effect of substrate surface oxides on the bonding of NiCr alloy particles HVAF thermally sprayed onto aluminium substrates, J. Therm. Spray Technol, 2010.

J. R. Davis, Aluminum and aluminum alloys, 1993.

M. S. Hunter and P. Fowle, Natural and Thermally Formed Oxide Films on Aluminum, Journal of The Electrochemical Society, vol.103, issue.9
DOI : 10.1149/1.2430389

A. Mcdonald, M. Xue, S. Chandra, J. Mostaghimi, and C. Moreau, Modeling fragmentation of plasma-sprayed particles impacting on a solid surface at room temperature, Comptes Rendus M??canique, vol.335, issue.5-6, pp.335-351, 2007.
DOI : 10.1016/j.crme.2007.05.006

S. Kitahara and A. Hasui, A study of the bonding mechanism of sprayed coatings, Journal of Vacuum Science and Technology, vol.11, issue.4, pp.747-753, 1975.
DOI : 10.1116/1.1312746

V. Pershin, M. Lufitha, S. Chandra, and J. Mostaghimi, Effect of Substrate Temperature on Adhesion Strength of Plasma-Sprayed Nickel Coatings, Journal of Thermal Spray Technology, vol.12, issue.3, pp.370-376, 2003.
DOI : 10.1361/105996303770348249

H. Steffens, B. Wielage, and J. Drozak, Interface phenomena and bonding mechanism of thermally-sprayed metal and ceramic composites, Surface and Coatings Technology, vol.45, issue.1-3, pp.45-299, 1991.
DOI : 10.1016/0257-8972(91)90236-P

C. Lea and C. Molinari, Magnesium diffusion, surface segregation and oxidation in Al-Mg alloys, Journal of Materials Science, vol.63, issue.10, pp.2336-2352, 1984.
DOI : 10.1007/BF01058110

. Matweb, Material property data Available from, 2008.

H. Zhang, X. Y. Wang, L. L. Zheng, and S. Sampath, Numerical simulation of nucleation, solidification, and microstructure formation in thermal spraying, International Journal of Heat and Mass Transfer, vol.47, issue.10-11, pp.47-2191, 2004.
DOI : 10.1016/j.ijheatmasstransfer.2003.11.030

R. Mcpherson, The relationship between the mechanism of formation, microstructure and properties of plasma-sprayed coatings, Thin Solid Films, pp.297-310, 1981.

W. Zhang, G. H. Wei, H. Zhang, L. L. Zheng, D. O. Welch et al., Toward the Achievement of Substrate Melting and Controlled Solidification in Thermal Spraying, Plasma Chemistry and Plasma Processing, vol.201, issue.3???4, pp.27-717, 2007.
DOI : 10.1007/s11090-007-9104-0

S. Dallaire, Influence of temperature on the bonding mechanism of plasma-sprayed coatings, Thin Solid Films, pp.95-237, 1982.

S. Wang, G. Wang, and E. F. Matthys, Melting and resolidification of a substrate in contact with a molten metal: operational maps, International Journal of Heat and Mass Transfer, vol.41, issue.10, pp.41-1177, 1998.
DOI : 10.1016/S0017-9310(97)00222-6

M. Bussmann, S. Chandra, and J. Mostaghimi, Modeling the splash of a droplet impacting a solid surface, Physics of Fluids, vol.12, issue.12, pp.3121-3132, 2000.
DOI : 10.1063/1.1321258

M. Bussmann, J. Mostaghimi, and S. Chandra, On a three-dimensional volume tracking model of droplet impact, Physics of Fluids, vol.11, issue.6, pp.1406-1417, 1999.
DOI : 10.1063/1.870005

V. Medhi-nejad, J. Mostaghimi, and S. Chandra, Air bubble entrapment under an impacting droplet, Physics of Fluids, vol.15, issue.1, pp.173-183, 2003.
DOI : 10.1063/1.1527044

A. Pershin, C. Mcdonald, and . Moreau, Numerical simulation of droplet impact on patterned surfaces, J. Therm. Spray Technol, vol.16, pp.713-721, 2007.

J. M. Cairney, R. D. Smith, and P. R. Munroe, Transmission electron microscope specimen preparation of metal matrix composites using the focused ion beam miller, Microstruct. Microanal, issue.6, pp.452-462, 2000.

N. Rowlands and P. R. Munroe, FIB for the evaluation of non-semiconductor materials, Microstruct. Sci, vol.26, pp.233-242, 1998.

A. P. Grosvenor, B. A. Kobe, and N. S. Mcintyre, Studies of the oxidation of iron by air after being exposed to water vapour using angled-resolved X-ray photoelectron spectroscopy and QUASES, Surf. Interface Anal, pp.36-1637, 2004.

J. U. Brackbill, D. B. Kothe, and C. Zemach, A continuum method for modeling surface tension, Journal of Computational Physics, vol.100, issue.2, pp.335-354, 1992.
DOI : 10.1016/0021-9991(92)90240-Y

C. Prakash and V. Voller, On the numerical colution of continuum mixture model equations describing binary solid-liquid phase change, Numer. Heat Transf., Part B Fundam, pp.15-171, 1989.

W. D. Bennon and F. P. Incropera, A continuum model for momentum, heat and species transport in binary solid-liquid phase change systems???I. Model formulation, International Journal of Heat and Mass Transfer, vol.30, issue.10, pp.30-2161, 1987.
DOI : 10.1016/0017-9310(87)90094-9

C. W. Hirt and B. D. Nichols, Volume of fluid (VOF) method for the dynamics of free boundaries, Journal of Computational Physics, vol.39, issue.1, pp.39-201, 1981.
DOI : 10.1016/0021-9991(81)90145-5

H. K. Versteeg and W. Malalasekera, An introduction to computational fluid dynamics: the finite volume method, 2007.

E. A. Brandes and C. J. Smithells, Metals reference book, 1983.

U. R. Evans, The corrosion and oxidation of metals. Scientific principles and practical applications, 1960.

R. M. Cornell and U. Schwertmann, The iron oxides: structure, properties, reactions, occurence and uses, 2003.
DOI : 10.1002/3527602097

S. Brossard, A. T. Tran, P. R. Munroe, and M. M. Hyland, Study of the Splat-Substrate Interface for a NiCr Coating Plasma Sprayed onto Polished Aluminum and Stainless Steel Substrates, Journal of Thermal Spray Technology, vol.468, issue.2, pp.24-30, 2010.
DOI : 10.1007/s11666-009-9419-x

R. Dhiman and S. Chandra, Freezing-induced splashing during impact of molten metal droplets with high Weber numbers, International Journal of Heat and Mass Transfer, vol.48, issue.25-26, pp.48-5625, 2005.
DOI : 10.1016/j.ijheatmasstransfer.2005.05.044

H. Fujimoto, Y. Shiotani, A. Y. Tong, T. Hama, and H. Takuda, Three-dimensionnal numerical analysis of the deformation behavior of droplets impinging onto solid substrate, Int. J. Multiph. Flow, pp.33-317, 2007.

S. Duhr and D. Braun, Why molecules move along a temperature gradient, Proc. Natl
DOI : 10.1073/pnas.0603873103

S. Chandra and C. Avedisian, On the collision of a droplet with a solid surface, Proc. R

L. Li, B. Kharas, H. Zhang, and S. Sampath, Suppression of crystallization during high velocity impact quenching of alumina droplets: Observations and characterization, Materials Science and Engineering: A, vol.456, issue.1-2, pp.35-42, 2007.
DOI : 10.1016/j.msea.2006.11.132

Y. M. Qiao and S. Chandra, Experiments on adding a surfactant to water drops boiling on a hot surface, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences, vol.453, issue.1959, pp.453-673, 1997.
DOI : 10.1098/rspa.1997.0038

S. Deshpande, S. Sampath, and H. Zhang, Mechanisms of oxidation and its role in microstructural evolution of metallic thermal spray coatings???Case study for Ni???Al, Surface and Coatings Technology, vol.200, issue.18-19, pp.5395-5406, 0200.
DOI : 10.1016/j.surfcoat.2005.07.072

N. Birks, G. H. Meier, and F. S. Pettit, Introduction to the high-temperature oxidations of metals, 2006.
DOI : 10.1017/CBO9781139163903

S. Taniguchi, N. Hongawara, and T. Shibata, Influence of water vapour on the isothermal oxidation behaviour of TiAl at high temperatures, Materials Science and Engineering: A, vol.307, issue.1-2, pp.107-112, 2001.
DOI : 10.1016/S0921-5093(00)01967-5

K. Volenik, F. Hanousek, P. Chraska, J. Ilavsky, and K. Neufuss, In-flight oxidation of high-alloy steels during plasma spraying, Materials Science and Engineering: A, vol.272, issue.1, pp.199-206, 1999.
DOI : 10.1016/S0921-5093(99)00478-5

C. Zhou, J. Yu, S. Gong, and H. Xu, Influence of water vapor on the isothermal oxidation behavior of low pressure plasma sprayed NiCrAlY coating at high temperature, Surface and Coatings Technology, vol.161, issue.1, pp.161-86, 2002.
DOI : 10.1016/S0257-8972(02)00398-5

C. Li and W. Li, Effect of sprayed powder particle size on the oxidation behavior of NiCrAlY materials during high velocity oxygen-fuel deposition, Surf. Coat. Technol, pp.162-193, 2002.

K. Volenik, V. Novak, J. Dubsky, P. Chraska, and K. Neufuss, Properties of alloy steel coatings oxidized during plasma spraying, Materials Science and Engineering: A, vol.234, issue.236, pp.234-236, 1997.
DOI : 10.1016/S0921-5093(97)00241-4

V. V. Sobolev and J. M. Guilemany, Effect of Oxidation on Droplet Flattening and Splat-Substrate Interaction in Thermal Spraying, Journal of Thermal Spray Technology, vol.8, issue.4, pp.523-530, 1999.
DOI : 10.1361/105996399770350205

M. E. Aalamialeagha, S. J. Harris, and M. Emamighomi, Influence of the HVOF spraying process on the microstructure and corrosion behavious of Ni-20%Cr coatings, J

O. Madelung, U. Rössler, and M. Schulz, Non-tetrahedrally bonded binary compounds II, 2006.
DOI : 10.1007/b71139

C. Li and Y. Wang, Effect of Particle State on the Adhesive Strength of HVOF Sprayed Metallic Coating, Journal of Thermal Spray Technology, vol.11, issue.4, pp.523-529, 2001.
DOI : 10.1361/105996302770348655

T. C. Totemeier, R. N. Wright, and W. D. Swank, Microstructure and Stresses in HVOF Sprayed Iron Aluminide Coatings, Journal of Thermal Spray Technology, vol.11, issue.3, pp.11-400, 2002.
DOI : 10.1361/105996302770348808

S. Kuroda, Y. Tashiro, H. Yumoto, S. Taira, H. Fukanuma et al., Peening Action and Residual Stresses in High-Velocity Oxygen Fuel Thermal Spraying of 316L Stainless Steel, Journal of Thermal Spray Technology, vol.10, issue.2, pp.367-374, 2001.
DOI : 10.1361/105996301770349457

D. Zhang, S. J. Harris, and D. G. Mccartney, Microstructure formation and corrosion behaviour in HVOF-sprayed Inconel 625 coatings, Materials Science and Engineering: A, vol.344, issue.1-2, pp.344-389, 2003.
DOI : 10.1016/S0921-5093(02)00420-3

A. P. Alkhimov, V. F. Kosarev, and A. N. Papyrch, A method of cold gas dynamic deposition, Dokl. Akad. Nauk. USSR, pp.318-1062, 1990.

M. Qu and A. Gouldstone, On the Role of Bubbles in Metallic Splat Nanopores and Adhesion, Journal of Thermal Spray Technology, vol.8, issue.2, pp.486-494, 2008.
DOI : 10.1007/s11666-008-9198-9

V. V. Sobolev and J. M. Guilemany, Investigation of coating porosity formation during high velocity oxy-fuel (HVOF) spraying, Materials Letters, vol.18, issue.5-6, pp.18-304, 1994.
DOI : 10.1016/0167-577X(94)90012-4

S. Brossard, A. T. Tran, P. R. Munroe, and M. M. Hyland, Study of the splat formation for plasma sprayed NiCr on aluminum substrate as a function of substrate condition, Surface and Coatings Technology, vol.204, issue.16-17, pp.204-2647, 2010.
DOI : 10.1016/j.surfcoat.2010.02.013

T. B. Massalski, H. Okamoto, P. R. Subramanian, and L. Kacprzak, Binary alloy phase diagrams, 1990.

. Friesen, Development and trends in HVOF spraying technology, Surf. Coat. Technol, pp.2032-2037, 0201.

R. S. Lima and B. R. Marple, Optimized HVOF Titania Coatings, Journal of Thermal Spray Technology, vol.12, issue.3, pp.360-369, 2003.
DOI : 10.1361/105996303770348230

N. Z. Mehdizadeh, M. Lamontagne, C. Moreau, S. Chandra, and J. Mostaghimi, Photographing Impact of Molten Molybdenum Particles in a Plasma Spray, Journal of Thermal Spray Technology, vol.14, issue.3
DOI : 10.1361/105996305X59422

K. Shinoda, H. Murakami, S. Kuroda, S. Oki, K. Takehara et al., High-speed thermal imaging of yttria-stabilized zirconia droplet impinging on substrate in plasma spraying, Applied Physics Letters, vol.90, issue.19, pp.90-194103, 2007.
DOI : 10.1063/1.2737360

W. J. Trompetter, M. Hyland, P. Munroe, and A. Markwitz, Evidence of Mechanical Interlocking of NiCr Particles Thermally Sprayed onto Al Substrates, Journal of Thermal Spray Technology, vol.14, issue.4, pp.524-529, 2005.
DOI : 10.1361/105996305X76568

C. Li and J. Li, Transient Contact Pressure During Flattening of Thermal Spray Droplet and Its Effect on Splat Formation, Journal of Thermal Spray Technology, vol.13, issue.2, pp.229-238, 2004.
DOI : 10.1361/10599630418158

L. Li, A. Vaidya, S. Sampath, H. Xiong, and L. Zheng, Particle Characterization and Splat Formation of Plasma Sprayed Zirconia, Journal of Thermal Spray Technology, vol.15, issue.1, pp.97-105, 2006.
DOI : 10.1361/105996306X92668

J. Stringer, B. A. Wilcox, and R. I. Jaffee, The high-temperature oxidation of nickel, p.20

. Wt, % chromium alloys containing dispersed oxide phases, Oxid. Met, vol.5, issue.1, pp.11-47, 1972.

M. Dorfman, Thermal spray processes, Adv. Mater. Process, issue.8, pp.47-49, 2002.

L. S. Hung, M. Nastasi, J. Gyulai, and J. W. Mayer, Ion???induced amorphous and crystalline phase formation in Al/Ni, Al/Pd, and Al/Pt thin films, Applied Physics Letters, vol.42, issue.8, pp.42-672, 1983.
DOI : 10.1063/1.94068

C. S. Giggins and F. S. Pettit, Oxidation of Ni-Cr-Al Alloys Between 1000?? and 1200??C, Journal of The Electrochemical Society, vol.118, issue.11, pp.118-1782, 1971.
DOI : 10.1149/1.2407837

A. Mcdonald, M. Lamontagne, S. Chandra, and C. Moreau, Photographing Impact of Plasma-Sprayed Particles on Metal Substrates, Journal of Thermal Spray Technology, vol.15, issue.4, pp.708-716, 2006.
DOI : 10.1361/105996306X147027

C. Lea and J. Ball, The oxidation of rolled and heat treated Al-Mg alloys, Appl

J. M. Ritchie, J. V. Sanders, and P. L. Weickhardt, Oxidation of a dilute aluminum magnesium alloy, Oxidation of Metals, vol.109, issue.1, pp.91-101, 1971.
DOI : 10.1007/BF00604741

S. Brossard, P. R. Munroe, A. T. Tran, and M. M. Hyland, Examination of the splat microstructure, splat-substrate interface and the effects of substrate heating on the splat formation for Ni-Cr particles plasma sprayed on to aluminum substrates, J. Therm. Spray Technol, pp.10-1007, 2010.

S. Brossard, P. R. Munroe, and M. M. Hyland, Study of the splat formation for HVOF sprayed NiCr on stainless steel substrates and the effects of heating and boiling pretreatments, pp.10-1007, 2010.

C. Moreau, P. Gougeon, and M. Lamontagne, Influence of substrate preparation on the flattening and cooling of plasma-sprayed particles, Journal of Thermal Spray Technology, vol.5, issue.1, pp.25-33, 1995.
DOI : 10.1007/BF02648525

M. Raessi, J. Mostaghimi, and M. Bussmann, Effect of surface roughness on splat shapes in the plasma coating process, Thin Solid Films, pp.506-507, 2006.

H. Liu, E. J. Lavernia, and R. H. Rangel, Modeling of molten droplet impingement on a non-flat surface, Acta Metallurgica et Materialia, vol.43, issue.5, pp.43-2053, 1995.
DOI : 10.1016/0956-7151(94)00386-V

M. Ivosevic, V. Gupta, J. A. Baldoni, R. A. Cairncross, T. E. Twardowski et al., Effect of Substrate Roughness on Splatting Behavior of HVOF Sprayed Polymer Particles: Modeling and Experiments, Journal of Thermal Spray Technology, vol.15, issue.4, pp.15-725, 2006.
DOI : 10.1361/105996306X146839

N. Ferguen, P. Fauchais, A. Vardelle, and D. Gobin, Numerical Investigation of Impact and Solidification of YSZ Droplets Plasma-Sprayed onto a Substrate: Effect of Thermal Properties and Roughness, 32nd International Conference on Advanced Ceramics and Composites
DOI : 10.1002/9780470456323.ch14

D. E. Wroblewski, R. Khare, and M. Gevelber, Solidification Modeling of Plasma Sprayed TBC: Analysis of Remelt and Multiple Length Scales of Rough Substrates, Journal of Thermal Spray Technology, vol.11, issue.2, pp.266-275, 2002.
DOI : 10.1361/105996302770348934

S. N. Basu, G. Ye, R. Khare, B. Mccandless, M. Gevelber et al., Dependence of splat remelt and stress evolution on surface roughness lenght scales in plasma sprayed thermal barrier coatings, Int. J. Refract. Met. Hard Mater, pp.27-479, 2009.

C. Li, C. Li, G. Yang, and Y. Wang, Examination of Substrate Surface Melting-Induced Splashing During Splat Formation in Plasma Spraying, Journal of Thermal Spray Technology, vol.15, issue.4, pp.717-724, 2006.
DOI : 10.1361/105996306X146947

W. Zhang, G. H. Wei, H. Zhang, L. L. Zheng, D. O. Welch et al., Toward the Achievement of Substrate Melting and Controlled Solidification in Thermal Spraying, Plasma Chemistry and Plasma Processing, vol.201, issue.3???4, pp.27-717, 2007.
DOI : 10.1007/s11090-007-9104-0

Y. Liu, T. E. Fischer, and A. Dent, Comparison of HVOF and plasma-sprayed alumina/titania coatings???microstructure, mechanical properties and abrasion behavior, Surface and Coatings Technology, vol.167, issue.1, pp.167-68, 2003.
DOI : 10.1016/S0257-8972(02)00890-3

Y. P. Wan, V. Prasad, G. Wang, S. Sampath, and J. R. Fincke, Model and Powder Particle Heating, Melting, Resolidification, and Evaporation in Plasma Spraying Processes, Journal of Heat Transfer, vol.121, issue.3, pp.121-691, 1999.
DOI : 10.1115/1.2826034